Numerical investigation on bowed blades of Iarge meridional expansion Turbine

To improve the performance of the Turbofan engine,several measures should be considered during design process.Such measures,relating to aerodynamic characteristic design,include the maximum enthalpy per stage,the shortest axial length,the minimum blade rows and the highest efficient in design and off design condition.To satisfy theses design characters,the meridian geometry of the engine will he excurvature at a high degree transition part between HP and LP turbines.The study is to investigate the effect of blade bowing on flow loss at blade tip and root of the type of turbine.Such turbine,tending towards separation,with severe secondary flow at the tip and strong radial flow at exit,was simulated by the 3D N-S solver Numerea,and there were several different stacking line bowing schemes in all.The results show that tip negative bowing and root positive bowing is able to weaken radial flow,consequently reduce the flow loss at the tip and root.     

数控超声磨削陶瓷叶片型面刀位轨迹计算

介绍了陶瓷超声磨削加工现状,建立了平行直纹面数学模型.分析了用圆柱磨轮四轴数控超声磨削平行直纹面时原理误差,并提出减小误差的措施,计算出磨轮空间轨迹,并进行陶瓷叶片型面超声磨削加工工艺试验.试验结果表明,超声磨削加工陶瓷叶片型面是可行的,所完成的刀位计算可有效减小原理误差.     

曲轴偏置机构原理在钢板滚切剪机设计中的应用

以空间七连杆滚切剪机运动轨迹方程为基础,采用某公司2800mm的曲轴偏置新型结构的单轴双偏心定尺滚切剪为研究对象。对曲轴偏置前后及不同偏置量的钢板剪切力、连杆力、保持剪刃间隙恒定的后滑道推力进行了分析对比。发现采用曲轴偏置后,在前曲柄提刀时刻机构仍然能够保持足够大的后滑道推力,机构在采用60mm-100mm的偏移量时后滑道压力同侧向力最接近平衡。理论分析结果及现场钢板剪切质量表明曲轴偏置机构在保持剪架在剪切过程中平稳,保证剪刃间隙恒定发挥了重要作用。     

Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.     

考虑冷变形加工硬化的翻边力理论计算

在分析现有计算公式存在不足的基础上,根据翻边变形区材料的应力应变特点,考虑了冷变形加工硬化(取幂函数硬化规律)和变形区材料厚度变化(翻边为变薄)两个因素的影响,利用金属塑性成形问题求解理论中的主应力法,推导和提出了圆孔翻边力计算的一个新公式.通过用钢板(SPCC)和铜板(T1)进行了翻边工艺试验的验证,并与经验公式和现有理论公式的计算结果进行了比较,表明新公式计算结果能接近于实际,且原理上更为科学合理.     

Characteristics of shell thickness in a slab continuous casting mold

The key to reduce shell breakout in the continuous casting process is to control shell thickness in the mold.A numerical simulation on the turbulent flow and heat transfer coupled with solidification in the slab mold using the volume of fluid (VOF) model and the enthalpy-porosity scheme was conducted and the emphasis was put upon the flow effect on the shell thickness profiles in longitudinal and transverse directions.The results show that the jet acts a stronger impingement on the shell of narrow face,which causes a zero-increase of shell thickness in a certain range near the impingement point.The thinnest shell on the slab cross-section locates primarily in the center of the narrow face,and secondly near the comer of the wide face.Nozzle optimization can obviously increase the shell thickness and make it more uniform.     

汽轮机叶片间流体流动的模拟研究

对超音速汽轮机的叶片间可压缩流体的流动情况进行了模拟研究。在对Giel等人的实验研究结果进行分析的基础上,将转子设计为流向转角为136°和轴向弦长为12.7 cm。通过Fluent软件对各种模型在湍流条件下反射边界情况(RBC)及非反射边界情况(NRBC)进行了二维数值模拟。研究结果对超音速汽轮机的优化设计提供了参考。     

高压蒸汽管道保温研究

计算了不同管径和保温厚度下蒸汽管道输送高压蒸汽的热损失和温度降。结果表明:保温厚度越大,蒸汽的热损失越小、温度降越小;保温材料导热系数与蒸汽的热损失呈正比;环境温度越高,蒸汽的热损失越小;环境风速对热损失的影响不大。同时研究了保温材料选择和保温结构对节能的影响。     

The Effects of Power Law Fluid Rheology on Coil Heat Transfer for Agitated Vessel in the Transitional Flow Regime

A CFD model of heat transfer from power‐law fluids to helical cooling coils in the transitional flow regime of a baffled tank mixed with a pitched blade turbine was developed with Fluent^TM. The model captured local temperature and velocity gradients. Simulations were run, varying Re, Pr, K and n. The results indicate that a Sieder‐Tate type correlation, with the exponent on and the coefficient in front of the Reynolds number being a function of n, is recommended for estimating ho. Also, a new two coil bank design was found to be more efficient when 450 < Re < 650.     

多孔介质微波加热厚度的确定

简述了微波加热的机理，以湿木材为研究对象，通过理论计算确定了微波在木材中的穿透深度。计算表明：随着木材含水率和微波工作频率的增加，微波在木材中的穿透深度减小；当用频率为915MHz和2450MHz的微波加热或干燥具有高含水率的多孔介质时，多孔介质的最大厚度应分别控制在16cm和6cm以内。