稀土对切玻璃金刚石锯片切削性能的影响

金刚石圆锯片可以用于切割玻璃和水晶制品。为了提高切割玻璃金刚石圆锯片的切割寿命和玻璃的切割质量．对切割玻璃金刚石圆锯片的胎体成分进行了优化设计，并在胎体材料中加入稀土化合物La2O3，同时对金刚石表面实施镀钛。本文从胎体材料对金刚石的把持力系数、实际切割的金刚石的脱落度以及锯片的切割速度方面，研究了稀土化合物在金刚石刀头胎体中的作用。结果表明：在胎体金属粉中加入适量的稀土化合物，胎体对金刚石的把持力系数有所改善，同时，增加了刀头胎体材料的脆性，实现了金刚石与胎体的同步磨损，金刚石的脱落度明显减小；切割速度比参比片提高了21．6％。     

Q235钢—冷模具钢轧制复合刀片的组织性能

本文对Ｑ２３５钢－冷模具钢轧制复合刀片的组织和性能进行了研究。结果表明，Ｑ２３５钢－冷模具钢轧制度合界面部位形成了冶金结合，轧制复合刀片的整体力学性能优于整体刀片和焊接复合刀片。     

反差增强剂厚度对磁粉检测缺陷检出率的影响

磁粉检测时,如果磁粉与工件表面的颜色对比度小,则容易造成小缺陷漏检。为了提高磁粉检测时的缺陷检出率,可在工件表面喷涂反差增强剂以提高对比度。试验研究了反差增强剂厚度对缺陷检出率的影响。结果表明:一定厚度的反差增强剂,可以提高对比度,对缺陷检出率的影响很小。     

基于射钉法的小方坯凝固过程数值模拟

结合方坯连铸机二冷各段的实际情况，在二冷各段末对铸坯进行射钉取样，利用硫印法测定方坯二冷区内目标点凝固壳的厚度，建立了方坯传热数学模型，并利用射钉结果修正数学模型中的各段的传热系数，提高数学模型的准确性。将射钉法确定的坯壳厚度与数学模型计算结果相比较，结果表明，利用修正过的数学模型可以模拟整个铸机的传热凝固过程。     

Effects of coating thickness and residual stresses on the bond strength of ASTM C633-79 thermal spray coating test specimens

Wire-arc-sprayed nickel-aluminum is widely used in the aircraft industry for dimensional restoration of worn parts and as a bond coat for thermal barrier coatings and other top coats. Some repair applications require thick coatings, which often result in lower bond strength. A mechanism being investigated to ex-plain this decrease in bond strength is the free edge effect, which includes both coating residual stresses and coating thickness. The layer-removal method was used to determine experimentally the residual stresses in wire-arc-sprayed nickel-aluminum coatings of different thicknesses. Bond strength evalu-ations were performed using an improved ASTM C 633-79 test specimen. Finite-element analysis and fracture mechanics were used to investigate the effects of coating thickness and residual stress state on coating bond strength.     

Oxide formation during etching of gallium arsenide

Characterisation of n-type GaAs, etched in a 5:1:1 mixture of H₂SO₄:H₂O₂:H₂O, was performed using X-ray photoelectron spectroscopy (XPS) and electrochemical AC impedance. Quantitative XPS analysis of GaAs indicated that the as-received wafers had a gallium-rich native oxide which was not affected by solvent degreasing treatments. Subsequent, oxidative etching formed a thinner arsenic-rich oxide. It is suggested that etching causes initial thinning of the native oxide; subsequently, transport of Ga and As ions occurs through the film by high-field ionic conduction. Arsenic enrichment in the resultant oxide film arises from the greater mobility of Ga³⁺ ions compared with As³⁺ ions as well as the relative solubility of Ga₂O₃ compared with As₂O₃. The as-received oxide film thickness, determined from the ratio of the oxide to substrate XPS peaks, was approximately 1.1 nm. After etching this was reduced to about 0.7 nm. This thickness is consistent with the driving voltage for oxide formation being provided by the electrochemical potential difference between hydrogen peroxide and the GaAs wafer (i.e. between 0.4 V, for As, and 1.2 V, for Ga, at a nm V⁻¹ ratio of 2). Capacitance measurements, derived from electrochemical impedance data, combined with film thickness data, gave a value of about 5 for the dielectric constant of As₂O₃.     

自动金刚石刀头磨弧机

针对采用激光焊接工艺的金刚石锯片上，其金刚石刀头内弧面需要磨抛的工艺要求，研发了一种自动金刚石刀头磨弧机。该设备将金刚石刀头放置在作间歇回转的工作转盘上，工作转盘由槽轮机构驱动；磨削砂轮安装在拖板系统上，拖板的间歇往复运动由一种在滑块上开有长槽的曲柄滑块机构实现，可满足工作转盘转位时，拖板停歇；工作转盘停歇时，拖板运动的工作要求。用靠模控制砂轮磨削的进给量。通过靠模的更换及设计能快速装卡的刀头夹具，可实现对不同弧度刀头的磨弧。本文介绍了该设备的结构组成、设计参数的选择及相关的设计方案，并对在滑块上开有长槽的曲柄滑块机构的设计方法进行了详细地讨论。     

橡胶冲裁模具刃口间隙的探讨与研究

阐述了合理选择丁基橡胶瓶塞冲裁模具的刃口间隙是提高模具使用寿命的关键，介绍了模具刃口间隙的确定方法。     

DEFORM-3D软件在叶片锻坯结构形式选取中的应用

在叶片锻造过程中,由于变形量大,锻出的叶片会出现如褶皱、裂纹这样的缺陷。为了提高生产效率,一般要求在螺旋压力机上一次锻造成形。因此,采用合理的毛坯结构形式在最小成形载荷下来获得最低程度的缺陷就显得十分重要。常规用来选择叶片锻坯合理结构形式的方法有诸多缺点,采用有限元方法将会在很大程度上弥补这些不足。     

组合式金刚石圆锯片创新及优化设计

传统金刚石圆锯片的有效切割宽度只有其直径的30～35％。为在普通规格的金刚石圆盘锯上低成本、高效率的加工大幅面石材制品，本文基于创新设计原理和圆锯片、锯机结构与功能的分析，将圆锯片分解为切割功能模块、支撑功能模块和驱动功能模块，提出新型组合式金刚石圆锯片基体的设计方案，使圆锯片的切割幅面达到其直径的2／3。应用有限元分析软件ANSYS，在结构分析、模态分析的基础上对组合式金刚石圆锯片基体径厚比、切割功能模块尺寸进行优化设计。结果表明：结构优化后的Ф1800mm组合式金刚石圆锯片基体质量减轻3．048kg，一阶固有频率提高3．235Hz，圆锯片直径和厚度均有所降低，动态性能更加稳定，结构更加合理。