HSLA-80/100钢的焊接

对ＨＳＬＡ－８０／１００钢的焊接性、焊接材料及焊接工艺进行了综述，并指出了现存在的主要问题。     

Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor

~~Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor     

关于混凝土钻芯取样法有关标准的讨论

本文对国内不同行业有关混凝土钻总取样方法的标准进行了讨论，供月行在使用和修订相应标准时参考。     

Solubility of amaranth seed proteins in sodium sulphate and sodium chloride: the main factor in quantitative extraction for analysis

Nitrogen was extracted more efficiently from amaranth seed with 0.04 M Na₂SO₄ (5% w/v) than with either 0.09 M or 0.17 M NaCl (5% or 10% w/v), despite both solutions having the same ionic strength (μ= 1). Solubility of saline soluble proteins (albumin ± globulin) was very poor in either water or 1M NaCl, but increased in 0.4M NaCl at alkaline pH between 7 and 10. Globulins were very soluble in 0.4M NaCl at a pH 9. Albumin was the main storage protein. Saline soluble proteins formed very weak gels.     

复合材料压缩破坏模式的缺陷敏感性

本文基于弹塑性分叉理论研究单向纤维增强复合材料的压缩破坏模式和压缩强度对缺陷的敏感性问题。对于常见复合材料,所得结论是:无缺陷或者小缺陷情况的破坏模式为倾斜破坏带;大缺陷情况的破坏模式为水平破坏带;形成水平破坏带的压力值小于形成倾斜破坏带的压力。     

PARASITIC TOLERANT DIFFERENTIAL SC TRANSCONDUCTANCE USING UNITY GAIN BUFFERS

The unity gain buffer will be good to design high frequency SCF if its resistiveeffects can be eliminated,and therefore the whole parasitic sensitivities will greatly be reduced.On the basis of this concept,a novel parasitic tolerant SC DTE(differential transconductanceelement)is proposed.SC floating inductor and integrator fit for high frequency applications areformed by the DTE.The computer simulation and experiment on a third order elliptic LP filterverify its validity.     

Evaluating Liquefaction Strength of Partially Saturated Sand

A method is presented for evaluating the liquefaction strength of partially saturated sand using the compression wave velocity (P-wave velocity), a new indicator of saturation. Based on laboratory test results, an empirical correlation that relates the liquefaction strength with the pore pressure coefficient B is firstly proposed. The strength is defined as the cyclic stress ratio required to cause liquefaction at a specified number of cycles. With the aid of a theoretical relation between B and the P-wave velocity, an explicit correlation of more interest is then established between the liquefaction strength of sand and its P-wave velocity. A comparison of the predictions using this explicit correlation with laboratory measurements shows a satisfactory agreement. The significance of this method lies in that it makes it possible to evaluate the liquefaction strength of sand as affected by saturation through the measurement of P-wave velocity, which can be made not only in the laboratory but particularly in the field.     

一种高并行度的H.264帧内预测器的VLSI设计

分析了帧内预测的17种模式,对于每个4×4大小块的16个像素点的不同模式的预测公式之间的相同运算,采用数字强度缩减的方法去除计算的冗余,提出了一种高并行度的帧内预测器,可以每个时钟周期处理16个像素点的预测值。基于SMIC0.18μm工艺,用verilog对该设计进行了VLSI实现,综合后的电路的关键路径最大时延为10ns,电路规模不超过1.4万门,数据吞吐率可以达到1600Msamples/s。从实现结果来看,与采用可重构方法的设计相比,该设计在相同的并行度下减小了电路面积,简化了控制逻辑。     

Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints

Addressing the potential for drop impact failure of Pb-free interconnects, the shear ductility after extensive aging of Sn-Ag-Cu (SAC) solders has been improved radically by Co or Fe modifications. Several other SAC+X candidates (X=Mn, Ni, Ge, Ti, Si, Cr, and Zn) now have been tested. Solder joint microstructures and shear strength results show that new SAC+X alloys also suppress void formation and coalescence at the Cu (substrate)/Cu₃Sn interface (and embrittlement) after aging at 150°C for up to 1,000 h. Microprobe measurements of 1,000 h aged samples suggest that Cu substitution by X is usually accentuated in the intermetallic layers, consistent with X=Co and Fe results.     

Cyclic strength of parts with overlapping zones formed by roller burnishing

The authors study residual stresses in and cyclic strength of shaft with overlapping zones formed during roller burnishing. The most significant decrease in fatigue strength is shown to occur in the presence of an overlapping zone with the areas arising due to a lowered roller burnishing pressure in the second pass. __________ Translated from Problemy Prochnosti, No. 3, pp. 144–148, May–June, 2006.