Rotordynamic forces generated by discharge-to-suction leakage flows in centrifugal pumps

In order to investigate the flow-induced vibration in the shroud passage of centrifugal pump and predict rotordynamic forces of centrifugal pump rotor system,an analysis of rotordynamic forces arising from shrouded centrifugal pump is presented. CFD techniques were utilized to analyze the full three-dimensional viscous,primary/secondary flow field in a centrifugal pump impeller to determine rotordynamic forces. Multiple quasi-steady solutions of an eccentric three-dimensional model at different whirl frequency ratios yielded the rotordynamic forces. The skew-symmetric stiffness,damping,and mass matrices were obtained by second-order least-squares analysis. Simulation of the coupled primary/secondary flow field was conducted,and the complex flow characteristics in the flow field of a shroud passage were achieved including the mean velocity and pressure,as well as the eddy in a large scale of flow field due to viscosity. The rotordynamic force coefficients were calculated,and the results were in good agreement with those of experiment except for the direct inertial coefficient without the consideration of whirling forces from the impeller primary flow passage.     

基于有限体积法的G4-73型离心风机三维流场数值模拟

基于有限体积法,利用Fluent软件对G4-73型离心风机内部流场进行了全三维数值模拟。结果表明:蜗壳内的低能流体区沿轴向朝流动方向推进;叶轮内的静压和动压在叶片吸力面靠近叶轮进口处最低,叶轮流道中动压等值线呈"凸"型分布,在叶片压力面靠近叶轮出口处静压和动压达到最大值,且叶轮出口相对总压损失集中在吸力面和前盘侧。     

Fabrication of a gradient refractive index preform using laminar shear mixing

A gradient refractive index rod was successfully prepared by a new fabrication method using laminar shear mixing, and a graded index polymer optical fiber that satisfied IEEE1394b was obtained from the method. To fabricate the gradient refractive index rod, a liquid monomer mixture with a relatively low refractive index was placed in a prepared cylindrical glass reactor and a transparent polymer rod with a higher refractive index was introduced at the center of the reactor. The reactor and the polymer rod were then rotated concurrently with a small rotating speed difference to generate a Couette flow in the liquid phase. The centrifugal force generated by rotation and the polymer diffusion into the liquid monomer mixture developed a graded concentration profile in a radial direction. The Couette flow could reduce the concentration fluctuation in a tangential direction. In addition, the graded index profile could be controlled by the copolymer composition of the rod and its diameter. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1100–1104, 2005     

气液两相机械搅拌釜中翼型组合桨持气特性

研究了机械搅拌釜中翼型组合桨的组合方式、桨间距、通气位置及翼型桨的排出流方向对气含率的影响。在单位体积功率消耗相同的情况下,采用以翼型k5桨为下层桨、较低的通气位置及较大的桨间距为搅拌釜的几何结构,并采用翼型桨的排出流方向向上的搅拌方式,可以提高搅拌釜的气含率。给出了气含率与单位体积功耗和表面气速的关联式。     

涡轮增压器叶轮低压铸造工艺设计及优化

采用UG NX8.0对某涡轮增压器叶轮的三维立体图进行有限元网格划分,应用ProCAST对铝合金叶轮的低压铸造充型过程和凝固过程进行数值模拟,利用VisualCAST对产生的缺陷进行可视化的对比,分析浇注温度、模具温度及压力-时间参数对铝液充型状态和凝固顺序的影响,并获得合适的低压铸造工艺参数。对试铸样品进行检测,结果表明:利用ProCAST可对叶轮的低压铸造工艺进行定量优化。     

遗传算法在离心泵叶轮设计中的应用

基于对旋转机械叶片参数化描述、叶栅流道网格参数化生成、流场数值模拟方法以及寻优算法的全局搜索性能四方面的研究,利用Blade Gen旋转机械叶片专业设计软件,对离心泵叶轮的叶型骨线、子午流面进行了参数化描述,并在Blade Gen中生成离心泵叶轮模型.利用Turbo Grid的高质量旋转机械六面体网格生成算法,对离心泵叶轮叶栅流道的网格进行拓扑计算及参数化控制,增大了后续流场分析的稳定性以及收敛速度.利用CFX的session文件,实现对CFX的后台参数化调用,建立了CFX环境下的完全自动化仿真分析过程.以Matlab为主控程序的方式,高效地整合了Blade Gen、Turbo Grid、CFX软件,建立了可扩展性好、鲁棒性强的离心泵叶片优化系统.     

Microstructures of functionally graded materials fabricated by centrifugal solid-particle andin-situ methods

Functionally graded materials (FGMs) belong to a relatively new class of inhomogeneous composite materials, in which the composition and/or microstructure undergo a gradual change along some directions. In this review article, the microstructures and composition gradients in Al/SiC, Al/Shirasu (volcanic eruptions commonly found in south Kyushu in Japan), Al/Al₃Ti, Al/Al₃Ni, Al/Al₂Cu FGMs have been investigated. The Al/SiC, Al/Shirasu and Al/Al₃Ti FGMs are fabricated by the centrifugal solid particle method where the distribution particles of SiC, Shirasu and Al₃Ti are solids in the melts. On the other hand, Al/Al₃Ni and Al/Al₂Cu FGMs are fabricated by the centrifugalin-situ method where Al/Al₃Ni and Al/Al₂Cu systems have lower liquidus temperatures than the processing temperatures. The feature of Al/(Al₃Ti−Al₃Ni) hydrid FGM, which is fabricated by a method combining both the centrifugal solid-particle andin-situ methods, is also shown.     

Numerical simulation and experimental investigation of two filling methods in vertical centrifugal casting

1 Introduction Titanium alloys possesses a high potential for production of work pieces with high strength, mechani- cal properties and high corrosion resistance, which makes them widely applied in aviation, astronavigation and civil fields[1- 5]. However…     

压缩机叶轮用钢——X12Cr13锻件工艺研究

通过对X12Cr13钢中奥氏体与铁素体的相匹配关系的研究,确定出该钢种合理的化学成分和合理的加热及热处理制度,解决了该钢在轧制、锻造等压力加工过程中易产生裂纹的问题。     

SHS-离心熔覆W-C-Fe金属陶瓷涂层的组织与耐磨性研究

以Fe2O3,WO3,Al,C为反应原料,采用SHS-离心法制备W-C-Fe内衬复合钢管。利用X射线衍射(XRD)、扫描电镜(SEM)分析了涂层的组织,用显微硬度仪测量内衬层硬度,并通过磨粒磨损试验测量了该涂层的耐磨性。结果表明,涂层组织包括主相Fe3W3C及少量的WC,W2C,Fe3C,Fe。涂层组织呈梯度分布,靠近基体处晶粒细小,远离基体处晶粒呈粗大树枝状。涂层硬度为13.5±1.6GPa。涂层的主要磨损机制为显微切削。涂层的相对耐磨性是淬火45#钢的16倍以上。