分流叶片对离心泵内部固液两相流的影响

为了研究分流叶片对离心泵内部固液两相流的影响,建立固液两相流模型,对无分流叶片离心泵和3种带分流叶片的离心泵进行全流道非定常数值模拟。重点分析了添加分流叶片对离心泵外特性、叶片表面压力脉动、叶片表面颗粒体积分数分布、叶片表面颗粒滑移速度的影响。分析结果表明:添加分流叶片以后,离心泵的扬程和效率均有显著的提高,叶片表面的颗粒分布更加均匀,叶片表面颗粒的滑移速度有不同程度的下降,使颗粒对叶片表面的磨损程度得以降低;当分流叶片的进口直径为0.65D2时,叶片出水边处的压力脉动幅值最小,减小了离心泵在运行过程中的振动和噪声。     

石油化工装备“后果分析”方法的介绍

石油化工装备的失效,由于所处理的物料常常是易燃易爆的化学品,所以往往导致发生燃烧、爆炸等,还可以波及附近的其它装置和设备发生连锁的失效和爆炸。为了分析这种严重事故可能造成的影响,研究防止这种事故的发生,近年来研究和发展了一种定量估计这种失效后果严重程度的方法,称为后果分析(Consequence Analysis)。通过分析,从这些设备的失效概率、可能发生的失效形式,研究设备内物料的泄漏形式、可能发生的后果、影响范围的大小、对周围装置、环境和人员的危害程度等,从而提出在设备设计、工厂的总图设计中采取的措施,以减轻其危害的程度。     

液氯离心泵的气蚀与防治

分析了影响液氯离心泵气蚀的两种参数：允许吸上真空度、气蚀余量。提出了泵气蚀的防治措施：提高离心泵基础设计质量，在实际使用中应采用高分子聚合材料涂覆，并进行补焊、补气。     

Rotordynamic forces generated by discharge-to-suction leakage flows in centrifugal pumps

In order to investigate the flow-induced vibration in the shroud passage of centrifugal pump and predict rotordynamic forces of centrifugal pump rotor system,an analysis of rotordynamic forces arising from shrouded centrifugal pump is presented. CFD techniques were utilized to analyze the full three-dimensional viscous,primary/secondary flow field in a centrifugal pump impeller to determine rotordynamic forces. Multiple quasi-steady solutions of an eccentric three-dimensional model at different whirl frequency ratios yielded the rotordynamic forces. The skew-symmetric stiffness,damping,and mass matrices were obtained by second-order least-squares analysis. Simulation of the coupled primary/secondary flow field was conducted,and the complex flow characteristics in the flow field of a shroud passage were achieved including the mean velocity and pressure,as well as the eddy in a large scale of flow field due to viscosity. The rotordynamic force coefficients were calculated,and the results were in good agreement with those of experiment except for the direct inertial coefficient without the consideration of whirling forces from the impeller primary flow passage.     

混合溶剂法脱除软沥青的喹啉不溶物

煤沥青中含有较多的喹啉不溶物会影响炭材料的性能。以软沥青为原料,采用混合溶剂离心法对其进行脱除喹啉不溶物试验研究。考察了芳烷比、溶剂比、离心时间、离心温度对精制沥青的喹啉不溶物含量和收率的影响。结果表明：当芳烷比一定时,精制沥青喹啉不溶物含量和收率随溶剂比的增大而减小;当溶剂比一定时,精制沥青喹啉不溶物含量和收率均随芳烷比的增大而增加;离心时间越长,所得精制沥青喹啉不溶物含量越低,收率也越低;离心温度升高,有利于喹啉不溶物脱除,离心温度的较优选择为80℃。通过调整混合溶剂的比例,可以方便地控制净化过程的收率和喹啉不溶物含量。     

基于有限体积法的G4-73型离心风机三维流场数值模拟

基于有限体积法,利用Fluent软件对G4-73型离心风机内部流场进行了全三维数值模拟。结果表明:蜗壳内的低能流体区沿轴向朝流动方向推进;叶轮内的静压和动压在叶片吸力面靠近叶轮进口处最低,叶轮流道中动压等值线呈"凸"型分布,在叶片压力面靠近叶轮出口处静压和动压达到最大值,且叶轮出口相对总压损失集中在吸力面和前盘侧。     

Fabrication of a gradient refractive index preform using laminar shear mixing

A gradient refractive index rod was successfully prepared by a new fabrication method using laminar shear mixing, and a graded index polymer optical fiber that satisfied IEEE1394b was obtained from the method. To fabricate the gradient refractive index rod, a liquid monomer mixture with a relatively low refractive index was placed in a prepared cylindrical glass reactor and a transparent polymer rod with a higher refractive index was introduced at the center of the reactor. The reactor and the polymer rod were then rotated concurrently with a small rotating speed difference to generate a Couette flow in the liquid phase. The centrifugal force generated by rotation and the polymer diffusion into the liquid monomer mixture developed a graded concentration profile in a radial direction. The Couette flow could reduce the concentration fluctuation in a tangential direction. In addition, the graded index profile could be controlled by the copolymer composition of the rod and its diameter. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1100–1104, 2005     

遗传算法在离心泵叶轮设计中的应用

基于对旋转机械叶片参数化描述、叶栅流道网格参数化生成、流场数值模拟方法以及寻优算法的全局搜索性能四方面的研究,利用Blade Gen旋转机械叶片专业设计软件,对离心泵叶轮的叶型骨线、子午流面进行了参数化描述,并在Blade Gen中生成离心泵叶轮模型.利用Turbo Grid的高质量旋转机械六面体网格生成算法,对离心泵叶轮叶栅流道的网格进行拓扑计算及参数化控制,增大了后续流场分析的稳定性以及收敛速度.利用CFX的session文件,实现对CFX的后台参数化调用,建立了CFX环境下的完全自动化仿真分析过程.以Matlab为主控程序的方式,高效地整合了Blade Gen、Turbo Grid、CFX软件,建立了可扩展性好、鲁棒性强的离心泵叶片优化系统.     

Microstructures of functionally graded materials fabricated by centrifugal solid-particle andin-situ methods

Functionally graded materials (FGMs) belong to a relatively new class of inhomogeneous composite materials, in which the composition and/or microstructure undergo a gradual change along some directions. In this review article, the microstructures and composition gradients in Al/SiC, Al/Shirasu (volcanic eruptions commonly found in south Kyushu in Japan), Al/Al₃Ti, Al/Al₃Ni, Al/Al₂Cu FGMs have been investigated. The Al/SiC, Al/Shirasu and Al/Al₃Ti FGMs are fabricated by the centrifugal solid particle method where the distribution particles of SiC, Shirasu and Al₃Ti are solids in the melts. On the other hand, Al/Al₃Ni and Al/Al₂Cu FGMs are fabricated by the centrifugalin-situ method where Al/Al₃Ni and Al/Al₂Cu systems have lower liquidus temperatures than the processing temperatures. The feature of Al/(Al₃Ti−Al₃Ni) hydrid FGM, which is fabricated by a method combining both the centrifugal solid-particle andin-situ methods, is also shown.     

Numerical simulation and experimental investigation of two filling methods in vertical centrifugal casting

1 Introduction Titanium alloys possesses a high potential for production of work pieces with high strength, mechani- cal properties and high corrosion resistance, which makes them widely applied in aviation, astronavigation and civil fields[1- 5]. However…