汉白玉废料制备球形纳米碳酸钙的研究

将汉白玉废料通过高温煅烧分解得到氧化钙,再用氯化铵循环液溶解氧化钙制得碱性氯化钙溶液,除去其中的Mg、Fe等杂质得到氯化钙精制溶液,利用化学方法合成得到碳酸钙粉体.用X射线衍射(XRD)、扫描电镜(SEM)及激光粒度分析仪、白度仪对碳酸钙产品的晶相组成、形貌、粒度分布、白度及化学组成进行了分析,所得产品为纯度达98.5%以上、白度达97%以上、平均粒度为80nm左右的球形纳米级碳酸钙.并对碳化反应速率及合成球形纳米碳酸钙的影响因素进行了分析.实验中循环使用NH4Cl,氨的排放量小,减少了环境污染.     

The hydration phase and pore structure formation in the blends of sulfoaluminate-belite cement with Portland cement

Sulfoaluminate-belite (SAB) cements are an attractive class of low-energy cements from the viewpoint of saving energy and releasing less CO₂ into the atmosphere during their production. Their hydraulic activity, however, does not match that of the ordinary Portland cement (PC) and needs improvement before they can be used on their own. However, SAB cements when blended with PC have the potential to be used effectively in traditional applications as shown by this study. Mortars made with blends of SAB cements and PC, and a cement-to-sand ratio of 1:3 by weight and a water-to-cement ratio of 0.5, indicate a superior protection against corrosion of steel to those made with blends of PC and blast-furnace slag (BFSPC). The prepared mortars were stored at 20 °C for 90 days under either a 60% relative humidity (RH)-dry air, or 100% RH-wet air conditions. With further improvement in the SAB cement quality through better understanding of their characteristics, a genuine competition between SAB/PC and BFSPC can be expected in practice.     

Stress Concentration Factors for a Circular Hole in Curved Beams Under Bending Loads

Abstract: As a contribution to the field of stress concentration studies, the case of circular hole in curved bar elements under bending is hereby studied. Trend values of stress concentration factors (SCF) are presented based on selected variables of the problem for two critical hole locations. The results will help to identify an SCF law for practical use by applying the statistical method of regression analysis. Two approximations obtained by means of computational methods are compared with those obtained by photoelastic experimental method.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

电液同步控制筒阀在小浪底水电厂的应用

小浪底水电厂位于多泥沙的黄河干流上，水轮机活动导叶会因磨损过大而严重漏水，在水轮机的设计上必须考虑这个因素;同时，为适应混水发电，小浪底水电厂机组采用了筒阀。文中介绍了筒阀的结构特点、功能及控制原理等，并对其在现场的实际应用情况进行了分析。     

A hexane solution deposition of SnS2 films from tetrabutyltin via a solvothermal route at moderate temperature

SnS₂ films have been deposited on glass and alumina plate substrates by the reactions between an organotin precursor [tetrabuyltin, (CH₂CH₂CH₂CH₃)₄Sn] and carbon disulfide in n-hexane at the temperature range 180-200 °C for 10-40 h. The reaction system was oxygen free and applied at a moderate temperature. The films so prepared were characterized by techniques of X-ray diffraction, Scanning electron microscopy, Raman and Mössbauer spectroscopies. The films deposited on glass as well as on alumina plate have an average thickness of 30 μm, but have different rose-like morphologies, which are influenced by both the anisotropic growths of crystals and the different substrate structures. Photoluminescence measurements show that the films have an emission peak at approximately 590 nm.     

Studies on the structural and ionic transport properties at elevated temperatures of La1−xMnO3±δ synthesized by a wet chemical method

Structural transformation and ionic transport properties are investigated on wet-chemically synthesized La_1−xMnO₃ (x=0.0–0.18) compositions. Powders annealed in oxygen/air at 1000–1080 K exhibit cubic symmetry and transform to rhombohedral on annealing at 1173–1573 K in air/oxygen. Annealing above 1773 K in air or in argon/helium at 1473 K stabilized distorted rhombohedral or orthorhombic symmetry. Structural transformations are confirmed from XRD and TEM studies. The total conductivity of sintered disks, measured by four-probe technique, ranges from 5 S cm⁻¹ at 298 K to 105 S cm⁻¹ at 1273 K. The ionic conductivity measured by blocking electrode technique ranges from 1.0×10⁻⁶ S cm⁻¹ at 700 K to 2.0×10⁻³ S cm⁻¹ at 1273 K. The ionic transference number of these compositions ranges from 3.0×10⁻⁵ to 5.0×10⁻⁵ at 1273 K. The activation energy deduced from experimental data for ionic conduction and ionic migration is 1.03–1.10 and 0.80–1.00 eV, respectively. The activation energy of formation, association and migration of vacancies ranges from 1.07 to 1.44 eV.     

Control of polymerization processes of 10,12-pentacosadiynoic acid LB films

Studies have been carried out on KrF excimer laser light (EX), X-ray or electron beam (EB) induced polymerization of 10,12-pentacosadiynoic acid (PDA) Langmuir-Blodgett (LB) films in relation to molecular density or molecular arrangement of the films using X-ray diffraction analysis, infrared (IR) spectroscopy and Raman spectroscopy. The molecular arrangement or density of the PDA LB films was controlled by subphase conditions when the films were built up, such as pH, temperature of a subphase or salt concentration in the subphase. Polymerization sensitivity of the PDA LB film was affected by the arrangement or molecular density. On low density (A type) films the polymerization occurred by irradiation with EX, X-ray or EB, but on high density (B type) films the polymerization occurred only when the irradiation was carried out by high energy beams such as X-ray or EB. Decomposition of polymerized films was observed further by excessive irradiation of EX or X-ray, but not on the B type films. It was revealed by X-ray diffraction analysis that in the A type film, the PDA molecules bent to a larger extent than those in the B type film and the polymerization proceeded topochemically, that is, the thickness decreased little after EB irradiation in a helium atmosphere. On the other hand, in the B type film, the thickness decreased by about 10% as a result of EB irradiation. By IR reflection-absorption (RA) and Raman measurements, it was confirmed that conjugated diacetylenic bonds disappeared and conjugated double and new conjugated triple bonds appeared after high energy beam irradiations. These results support the supposition that 1,4-polymerization, i.e. polydiacetylene type polymerization, occurs easily in the A type film and 1,2- or 3,4-polymerization, i.e. polyacetylene type polymerization, occurs in the B type film, and that the polymerized A type film was decomposed at the polydiacetylenic bond when the irradiation continued further. It was also shown that the polyacetylene type polymer was obtained only when the B type film was irradiated with the high energy beam.     

日本“绿色”包装的系统化理念及其启示

本文通过对日本包装系统的考察和与中国包装现状的对比,阐述了“绿色”包装系统的基本理念和构建要素,总结出必须通过科技、法制等使包装产业形成一个系统化的“生态链”,使包装业真正造福于人类。