Influence of the Preheat Treatment on the Microstructure and Properties of X37CrMoV5-1 Steel

The technological properties of the hot-work tool steels depend on their microstructural quality induced by the production process and the heat treatment. One of the frequently applied methods to improve microstructure is preheat treatment. The treatment of carbonitriding X37CrMoV5-1 steel has been investigated in fluidized bed furnaces. Thickness and phase composition have been conducted using optical microscopy Neophot 32 and scanning microscopy, JEOL 5400, after etching in nital.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

小型微/纳米级三坐标测量机的研制

介绍一套低成本小型三维坐标测量机的研制过程，作为微/纳米级超精密测量设备，整体机台结构采用花岗岩材料；X／Y轴的移动平台利用压电材料摩擦驱动与挠性变形原理，长短两行程可达25mm范围及5nm的微位移，藉自行研发的衍射干涉激光尺，位置回馈测量系统可具有0．025nm的分辨率；测量探头在一般DVD光读取头的自动聚焦原理基础上改装，最佳分辨率可达2．5nm，该雏形机适于测量微机电组件、微型器件及膜厚等。     

在ad hoc网络中一种新的节能路由切换模型

提出了一种基于能量消耗的路由切换模型(ERHM),它在路由维护中利用切换技术来使路由的能量消耗最小.仿真结果表明采用切换技术的ERHM模型的能量节省量要比不采用切换技术节约1.5～7.5倍,且节点的移动性越大,能量节约越多.     

弱导光纤的标量衍射光束特性分析

仿照罗兰圆光学系统构造罗兰球光学系统 ,在罗兰球中简化电磁波的瑞利 索末菲标量衍射积分公式 ,推导出折射率阶跃分布的弱导光纤LP模衍射场分布和空间频谱的计算公式。提出LP0 1模远场衍射分布存在类似于平面波圆孔夫琅禾费衍射艾里斑的中央亮斑概念 ,并给出中央亮斑角半宽度的计算公式。     

贯流式水轮发电机集电环短路原因分析及改善措施

白石窑水电厂1～4号发电机组在投运初期,集电环曾多次出现绝缘降低甚至短路的非正常现象。通过分析,引发故障的原因主要是碳刷架、集电环绝缘结构设计欠妥、运行环境恶劣以及机组的振动过大。针对上述原因,改进了绝缘结构设计上的不足,加强巡视和维护检查,装设工业电视监控,加装碳粉回收装置,对受油器进行防漏油或喷油技术处理,加强清污力度、提高发电水头以便减少机组振动,从内外因加以防范和改善后,问题得到了标本兼治,取得了理想的效果。     

电控平行排列液晶光栅的光衍射特性研究

对电控平行液晶光栅的理论进行了分析,并配以结构原理图。通过对平行排列及90°扭曲排列液晶指向矢的计算,得出液晶盒中相应的折射率、相位差与电压之间的关系图,两者经比较证明平行排列更具适用性,并在实验中观测到了平行排列液晶光栅衍射特性与电压的关系。     

正交参数与平纹面

本文证明了一族闭曲线C(t),t∈I,称变闭曲线,在光滑性条件下,具有正交参数u,即当C(t)表为(?)=(?)(u,t)时,有(?)·(?)≡0.接着,文中提出了一种“降维法”,即用一族平行平面将空间曲面截成平面变曲线,并讨论其若干整体性质.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

基于米氏散射及夫朗和费衍射的FAM激光测粒仪

提出了综合运用夫朗和费衍射和米氏散射，即在大粒径范围内采用夫朗和费衍射理论，而在小粒径范围内采用米氏散射理论，来改善小粒径范围内的测量精度，保证激光测粒仪在整个粒径范围内的测量精度。