人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。     

静态电子轨道衡组成部分解析及其合理选择

阐述静态电子轨道衡诸多优点;工作原理、允许误差及误差分配;轨道衡的结构组成部分、解析各部分的工作特性及技术指标要求;合理选配及推荐实例.     

线缆护套材料在我国西部环境中的试验研究

本文通过对线缆外护套材料在我国西部地区严酷环境试验站中土壤和大气1～5年的试验结果分析，总结了塑料护套材料的耐蚀性能。为线缆护套的防护设计、合理选材及制定标准提供科学依据。     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

Excel在大学物理实验中的应用

利用Excel的强大功能，对实验数据进行处理、分析，对实验过程及实验结果的监控。     

论社区服务产业化

社区经济作为一种优化的资源配置方式，利用社区服务为载体，将社区内互不相联的各种经济成份变为利益共同体，建立一种新的经济生产方式，从而带动社区乃至更广区域的经济发展。     

Prediction of spectral reflectance factor distribution of automotive paint finishes

It is necessary to determine the accurate reflectance of painted surfaces for the review of paint finishes by computer graphics (CG) before actual painting of the exterior color of automobiles, and for quality control during production and inspection processes. We have optimized a method for measuring reflectance by using a statistical technique. We have found that the reflectance of a painted surface is best measured at an incident angle of 60° and at five aspecular angles of 10°, 18°, 28°, 40°, and 90°. Our method makes it possible to accurately reproduce reflection characteristics of paint finishes containing special flake pigments, such as pearl mica. Also it was proved that our method can apply not only to solid and metallic coatings but to all painted surfaces. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 275–282, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20125     

Drying of Uncoated Paper with Gas-Fired Infrared Emitters—Optimum Emitters' Location Within a Paper Machine Drying Section

This article theoretically investigates the drying of uncoated paper with gas-fired infrared (IR) emitters installed within the drying section of a given commercial paper machine. Specifically, it presents the ideal location of two opposing IR emitters within the drying section. The ideal location of the two opposing IR emitters corresponds to the highest machine speed with specified average moisture content of paper sheet at the end of the drying section. This article also presents the average evaporation rate, temperature, and moisture content of the paper sheet as it travels through the drying section with the two opposing IR emitters operating at the optimum location. In addition, the temperature and moisture profiles in the sheet thickness direction, before and after the IR emitters, are provided. This article is not concerned with the potential effects of drying with IR emitters on paper sheet properties and machine runnability issues.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.