Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

厚度控制技术在中厚板轧制生产中的应用

本文探讨了影响中厚板厚度波动的因素，结合安钢中板厂2800mm轧机按合同轧制一批交货重量不大于理论重量船板的生产实践，总结了实际生产中实现高精度厚度控制的有效方法。     

Experimental results of a low-power roadheader driving a gallery with different types of rock at the face

In this paper, the experimental results of a 45-kW and 15-t roadheader excavating a gallery with two different types of rock at the face using two different cutting heads are shown. It is proved that the roadheader works properly with both cutting heads. In comparison with other results in the literature, the principal parameters, i.e. specific energy, cutting rate and tool wear, are at a level that can be considered satisfactory taking into account the low power of the roadheader. On the other hand, the influence of the number of picks, which is the main difference between the two cutting heads, on the operational parameters is shown.     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

�¸�������в������Ȼ�����꾮�ٶȵ�;��

本文针对天然气井提高钻井速度问题,总结分析了盆地中部井身结构,水力、机械参数,聚合物钻井液,正注反挤固井等工艺技术对该地区钻速的影响。指出提高天然气井钻井速度,必须搞好系统工程,形成配套技术。     

HS－2000型双反射镜补偿式高速摄影系统研究

介绍ＨＳ─２０００双反射镜补偿式高速摄影系统的补偿原理、结构及其试验结果。     

Study on Factors Affecting the Structure of High SpeedSteel Ingot Produced by ESR

ＳｔｕｄｙｏｎＦａｃｔｏｒｓＡｆｆｅｃｔｉｎｇｔｈｅＳｔｒｕｃｔｕｒｅｏｆＨｉｇｈＳｐｅｅｄＳｔｅｅｌＩｎｇｏｔＰｒｏｄｕｃｅｄｂｙＥＳＲＬｉＺｈｅｎｇｂａｎｇ；ＣｈｅＸｉａｎｇｑｉａｎＡｂｓｔｒａｃｔ：Ｔｈｅｉｎｆｌｕｅｎｃｅｏｆｔｈｅｍｅｔａｌｐ...     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

锁相技术在电子束曝光机工件台稳速控制中的应用

采用锁相技术，对电子束曝光机工件台运动实现速度环的全数字控制。设计了数字差频积分回路和数字差频比例控制器，能有效消除速度的静态误差和改善系统的动态特性。     

28Cr2Mo1VA钢变速冷却转变动力学研究

用膨胀法对28Cr2Mo1VA钢测定了变速冷却过冷奥氏体转变动力学曲线,结果表明,先慢冷后快冷,珠光体、贝氏体转变滞后;反之,转变超前。并提出用图解计算法求转变点,结果与实验相符合。