强折射轴对称流场的干涉再现方法

利用光学方法测量气体状态参数的关键在于确定气体折射率场的变化。光线通过稳定的非均匀折射率场时发生偏折，并且在强折射对称场中会产生交叉，使得条纹位移量的判读困难。本文首先分析了光线在轴对称折射率场中的偏折效应，在此基础上，给出了一种利用成像透镜对强折射轴对称场中折射率的干涉再现方法。该方法与其它方法相比较能够精确地确定折射率ｎ（ｒ）的值。     

多信道光纤环形网络结构分析

本文对多信道光纤环形网络结构进行了详细分析，推导出环网内平均路经长度和最大直径计算公式，并分析了最佳多信道光纤环网结构。     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

苯并口恶嗪-环氧化合物-胺类催化剂体系开环聚合反应的研究

采用TLC，GPC，1H－NMR及IR等分析方法，对苯并恶嗪－环氧化合物－胺类催化剂体系的聚合反应进行了研究，表征了产物结构，并探讨了聚合反应机理，结果表明，苯并恶唪－环氧化合物体系在胺类催化剂如苄胺，咪唑的作用下，能发生开环聚合反应，生成低分子量的聚合物。     

接触网零件振动试验方法探讨

通过对接触网零件用紧固件的耐振动性能进行振后扭矩测试和横向振动采用压力环测试应变进行对比分析，提出了合理的接触网零件耐振动性能试验方法。     

Tribological issues in reducing piston ring friction losses

In this paper improvement in fuel economy by reducing piston ring friction is studied and reduction of piston ring tension and the use of two-ring packages are found to be effective. However, these can be accompanied by adverse effects such as excessive wear and increasing oil consumption, and measures to overcome these problems are studied in detail.     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

On the stability preserving property of the double bilinear transformation on a class of 2-D transfer functions

This paper addresses the BIBO (bounded-input bounded-output) stability of a class of discrete 2-D quarter-plane filters in the presence of nonessential singularities of the second kind (NSSK's) on the unit bidisk. Conditions under which the double bilinear transformation (DBT) preserves stability are derived. The results presented here also extend the class of systems whose stability can be predicted. Use of the inverse DBT to produce a continuous equivalent of the discrete 2-D transfer function allows easy application of a continuous-domain equivalent of a criterion developed by Dautov. The necessary and sufficient condition for stability derived in this work provides a simple check for the class of systems under consideration. From this class of systems, it is also possible to construct stable pairs of mutually inverse transfer functions.     

CMOS电路中抗Latch-up的保护环结构研究

闩锁是CMOS集成电路中的一种寄生效应,这种PNPN结构一旦被触发,从电源到地会产生大电流,导致整个芯片的失效。针对芯片在实际测试中发现的闩锁问题,介绍了闩锁的测试方法,并且利用软件Tsuprem4和Medici模拟整个失效过程,在对2类保护环(多子环/少子环)作用的分析,以及各种保护结构的模拟基础之上,通过对比触发电压和电流,得到一种最优的抗Latch up版图设计方法,通过进一步的流片、测试,解决了芯片中的闩锁失效问题,验证了这种结构的有效性。     

对水厂一期滤池技术改造后的经济评价

本文主要从经济角度分析净水厂实际生产情况及经济技术指标等方面的数据。阐述福州西区水厂一期滤池由原先双阀滤池改造成V型滤池的经济性。