A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

Formation of low-resistivity poly-Si and SiNx films by Cat-CVD for ULSI application

In this paper, bulk-Si metal–oxide–semiconductor field effect transistors (MOSFETs) are fabricated using the catalytic chemical vapor deposition (Cat-CVD) method as an alternative technology to the conventional high-temperature thermal chemical vapor deposition. Particularly, formation of low-resistivity phosphorus (P)-doped poly-Si films is attempted by using Cat-CVD-deposited amorphous silicon (a-Si) films and successive rapid thermal annealing (RTA) of them. Even after RTA processes, neither peeling nor bubbling are observed, since hydrogen contents in Cat-CVD a-Si films can be as low as 1.1%. Both the crystallization and low resistivity of 0.004 Ω·cm are realized by RTA at 1000 °C for only 5 s. It is also revealed that Cat-CVD SiN_x films prepared at 250 °C show excellent oxidation resistance, when the thickness of films is larger than approximately 10 nm for wet O₂ oxidation at 1100 °C. It is found that the thickness required to stop oxygen penetration is equivalent to that for thermal CVD SiN_x prepared at 750 °C. Finally, complementary MOSFETs (CMOSs) of single-crystalline Si were fabricated by using Cat-CVD poly-Si for gate electrodes and SiN_x films for masks of local oxidation of silicon (LOCOS). At 3.3 V operation, less than 1.0 pA μm⁻¹ of OFF leakage current and ON/OFF ratio of 10⁷–10⁸ are realized, i.e. the devices can operate similarly to conventional thermal CVD process.     

The Effect of Moisture Content on the Conversion of Ergosterol to Vitamin D in Shiitake Mushrooms

The distribution of ergosterol in different parts of shiitake mushrooms was studied in order to optimize the conversion of ergosterol to vitamin D₂ during drying. The effect of moisture on the conversion of ergosterol to vitamin D₂ was also investigated by adjusting the moisture content of fresh mushrooms to different levels in a large vacuum desiccator and subjecting them to UV irradiation at 290-320 nm wavelength, for 2 h. The moisture, ergosterol and vitamin D₂ contents were determined using standard procedures. It was found that the ergosterol content on a dry matter basis of fresh shiitake mushroom was highest in the gills (10.6 ± 0.99 mg/g DM), followed by the cap or pileus (5.34 ± 0.64 mg/g DM) and was least in the stalk or stipe (2.97 ± 0.56). The moisture content had a marked influence on the conversion of ergosterol to vitamin D₂, the best conversion taking place at a moisture content of about 70% on a wet basis.     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

气体悬浮焙烧炉内衬烘炉曲线的确定

根据所使用的低水泥浇注料的性能，对中铝山西分公司检修厂4号焙烧炉制定了合理的烘烤曲线，提高了耐火内衬的质量，延长了内衬的使用寿命。     

A comparative study of short nylon fiber—Natural rubber composites prepared from dry rubber and latex masterbatch

A novel method for the preparation of short nylon fiber–natural rubber composites was developed in which short fibers chopped to approximately 6 mm were incorporated in the latex stage and processed into sheet form. By this method, mixing cycle time was reduced without compromising the fiber dispersion. Fiber breakage during mixing was reduced. The new composites when compounded with a dry bonding system based on hexamethylenetetramine, resorcinol and hydrated silica (HRH) showed improved modulus, tensile strength and abrasion resistance compared to conventional composites. Tear strength, resilience, and compression set were similar to the conventional composites. SEM analysis indicated better interaction between matrix and fibers in the case of latex master batch. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Prediction of the twisting moment and axial force in a circular rubber cylinder for combined extension and torsion based on the logarithmic strain approach

The scope of the present work is the application of a particular class of strain energy function, based on the logarithmic strain, for the prediction of the twisting moment and axial force of a rubber circular cylinder under combined extension and torsion. The strain energy function involves four material parameters three of which are determined by fitting published experimental data from simple tensile and compression tests of natural rubber. One of the parameters of the proposed model has physical meaning, and it is equal to one ninth of the initial modulus of elasticity of the material. Hence, the number of unknown parameters is reduced to three. The logarithmic strain energy function is then applied to a combined extension and torsion problem of a rubber circular cylinder to check its performance for more complicated deformations. The results are compared with corresponding experimental and theoretical solutions available in the literature to validate the proposed model. It is found that the proposed strain energy function apart from predicting the common modes of deformations is also capable to determine more complicated types of deformation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphological aspects of rubber fracture and wear

Morphology of carbon black (CB)‐filled rubber was studied with AFM and SEM and the classification of filler agglomerates, based on their internal structure and filler–matrix interactions, has been proposed. It varies according to the activity of CB and the kind of rubber. It has been shown that fracture of rubber starts either inside filler agglomerates (de‐cohesion) or in a filler–matrix interphase (de‐adhesion) initiating wear of the material. Microscopic observations correlate well with TGA and EPR data of wear debris collected during friction of rubber. The increase of thermal stability of CB and the appearance of additional spin signals, respectively, for elongated samples or debris, are proposed to be associated with de‐cohesion or de‐adhesion of the agglomerates. New approach to the fracture of rubber called “fatal agglomerate concept” is presented. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

尾矿回收超细绢云母工艺及产品应用研究

从选矿尾矿中回收超细绢云母粉工艺是近几年发展起来的一项资源综合利用新工艺。研究从尾矿的工艺矿物学入手，介绍了尾矿的矿物组成及回收工艺的工作原理，着重探讨了超细绢云母粉在橡胶、塑料、涂料等领域中的应用情况。