Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

水浴法加温液氧泵

1　故障现象一次 ,我们用KL -1 5型制氧制氮车开机制氮 ,给一只容积为 40升、最高工作压力为1 4 7MPa的气瓶灌充氮气 ,当气瓶充气压力升高到一定值时不再上升。反复开泵 ,压力基本不变。液氧泵停止时 ,出口压力无明显下降。经分析判断导致气瓶压力升高到一定值时不再上升的原因是由于液氧泵被冻结所致。2　排除方法首先关闭液氧泵。拧开制冷机氢气放气阀 ,使压力下降到 1 0MPa。开大放气阀 ,使二级压力保持在 0 3 5MPa左右。调整正流空气调节阀 ,调节好中部温度。关闭液氮进液氧泵阀和气氮出液氧泵阀。戴棉布手套 ,拆开液氮进口接头、…     

滚动转子式压缩机传热模拟

就滚动转子式压缩机的传热特性进行了分析。把压缩机分为15块，视摩擦损失和电机发热为内热源，考虑润滑油流动在传热过程中的影响，应用集中参数法对每块进行了能量分析，建立了传热数学模型并进行了计算。     

取水泵站调速运行的节能效果比较

对取水泵站水泵部分调速运行和全部调速运行在水源枯水位、常水位及洪水位时的节能效果进行了分析比较 ,并给出了结论     

浅埋地下建筑风冷热泵空调系统传热模型与试验研究

本文在浅埋地下建筑风冷热泵空调系统围护结构传热动态模拟的基础上，通过对南京市太园地下旅社围护结构传热的实时测试，验证动态传热模型及计算机模拟方法的可行性和正确性，为浅埋地下建筑风冷热泵空调系统的装机容量、节能指标和设计计算提供一定的理论依据。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

化学成分和固溶温度对1Cr17Mn9Ni4N不锈钢组织和性能的影响

为提高1Crl7Mn9Ni4N钢固溶处理后的力学性能(特别是钢的强度)，研究了化学成分及固溶处理温度对其组织和性能的影响。结果表明，1000—1125℃固溶处理后，该钢的组织为单相奥氏体。在标准成分范围内，随着镍、锰含量的增加，该钢的强度降低，塑性有所改善。氮明显提高该钢的强度。根据试验结果，每增加0．01％的氮钢的室温强度可提高大约5MPa，且塑性基本上不受影响。当合金成分(质量分数，％)控制在C0．08—0．12、Crl6．5—17．5、Ni3．5—4．2、Mn8．0—9．0、N0．22—0．28时，1Crl7Mn9Ni4N钢经1050—1100℃固溶处理后强度较高、塑性好，室温强度σ0．2和σb可分别达到400MPa和800MPa。     

The extracorporeal circuit: Materials,problems, and solutions

The extracorporeal circuit in hemodialysis and related therapies facilitates passage of blood to and from the patient and forms an integral link with the safety systems of the proportioning system. Historically, elements of the circuit were subject to problems such as spallation introduced by the blood pump and plasticizer from the tubing sets leaching into the blood. Many of these early issues have been largely resolved, although there is still potential for further improvement and innovation. The introduction of such improvements and innovations into clinical practice is critically dependent upon their cost and benefit to patient and renal unit staff.     

链条锅炉的节能改造

本文针对株洲硬质合金厂SHL20—13—AII型20t蒸汽链条锅炉存在的问题，进行了节能改造，取得了显著的成效。     

软启动器在深井泵电动机上的应用

论述了几种三相交流异步电动机的起动方式及其优缺点 ,介绍了新型的电子软启动方式在我厂深井泵电动机上的应用及取得的运行效果 ,为电动机软启动方式在工矿企业中的应用提供了应用经验。