A sensitivity analysis of the linear complementarity programming model: Appalachian steam coal and the natural gas market

There have been extensive attempts in recent years to perform spatial equilibrium analysis of commodity markets, particularly that of energy. Most of these attempts have been based on linear programming transportation models, and more recently quadratic programming models. Unfortunately, neither of these modelling approaches can deal with the case of multi-commodity analysis with non-symmetric regression coefficients. In this paper, we overcome this problem by employing the linear complementarity programming model. In addition, we show how the model can be applied to coal and gas energy flows within a single region. Future potential applications of the model are also implied.     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.     

Dynamic analysis of the NPP pressure sensor system

The aim of the work was to develop on-line methods of control and diagnostics of pressure sensors at a NPP. The analysis was carried out along two lines:

1. i) The detection system including the sensor itself was modeled theoretically to obtain and study its transfer function, and to establish correspondence between the spectral characteristics of the pressure signal.

2. ii) The numerical processing of the signal using the AR technique to reconstruct the transfer function and evaluate the system's response, to a step impulse, as well as the spectral analysis. The hydraulic model presented indicate that the spectral lines observed at 10 Hz are due to longitu-dinal oscillations of water in the system branches, while the response time of the detection system is effectively the time of signal retardation in the porous ceramic diaphragms of the δ-cell of the sensor itself.

     

ANALYSIS OF EXPERIMENTAL AND NUMERICAL RESULTS OF A TURBULENT SWIRLING FLOW IN A TUBE

In many applications swirling flow is used to enhance heat and mass transfer. One of the problems of modelling a turbulent swirling flow is the choice of the turbulent closure model which is acceptable for engineering purposes. To evaluate which model performs best, numerical results are compared with experimental data. Local velocity measurements are carried out on a swirling flow in a circular tube. The measurement method is hot-wire anemometry combined with visualization techniques. The numerical analysis is carried out using the k-ε model and the Algebraic Stress Model. In the experiment a symmetrical swirl was observed, Comparing the experimental data with the numerical results shows that the Algebraic Stress Model represents the experimental data quite well, whereas the k-ε model fails.     

CAD与CAPP集成研究回转体类零件特征识别

本文研究了回转体轴类,轴套类零件的特征识别。对这类零件常用的特征单元进行了定义,描述了这类零件的特征模型:介绍了它的识别方法和特征参数定义方法。     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

Effect of deposition conditions on the properties and annealing behavior of cold-sprayed copper

The deposition of copper by cold gas dynamic spraying has attracted much interest in recent years due to the capability to deposit low-porosity oxide-free coatings. However, it is generally found that as-deposited copper has a signicantly greater hardness, and potentially lower ductility, than bulk material. In this article, copper was deposited by cold spraying using helium as the driving gas at both 298 and 523 K. Evidence is presented indicating that the material sprayed at the lower temperature exhibits a lower dislocation density throughout the grain structure than the material sprayed at the higher temperature. The low stacking fault energy of copper restricts recovery during annealing, and thus microstructural changes during annealing only proceed once recrystallization begins. The material sprayed at low temperature (with the low dislocation density) exhibited recrystallization at annealing temperatures as low as 373 K with a corresponding reduction in hardness. However, the copper sprayed with helium at 523 K was resistant to annealing at temperatures up to 473 K where the dislocations in the structure prevented recrystallization. However, at higher temperatures, recrystallization did proceed (with corresponding reductions in hardness). The fracture behavior of the copper that was cold sprayed with helium at 523 K, both in the as-sprayed condition and following annealing, was measured and explained in terms of the annealing mechanisms proposed. The original version of this paper was published in the CD ROM Thermal Spray Connects: Explore Its Surfacing Potential, International Thermal Spray Conference, sponsored by DVS, ASM International, and HW International Institute of Welding, Basel, Switzerland, May 2–4, 2005, DVS-Verlag GmbH, Düsseldorf, Germany.     

Influence of initial textures on dynamic recrystallization and textures in AZ31 magnesium alloys

1　INTRODUCTIONMagnesiumisthelightestmetallicstructurema terialwithhighspecificstrengthandthereforeiswidelyusedinautomotive ,electronicsandaerospaceindustries[1,2 ] .However ,magnesiumoftenshowsinsufficientplasticityatroomtemperatureduetoitsHCPstructurewithlessindependentsystemsofbasalslip .Toenhanceformabilityofmagnesium ,ahigherdeformingtemperatureisusuallyusedwithtwopur poses .Thefirstistoactivatenewslipsystemsbesidesbasalslip ,sothatmorethanfiveindependentslipsystemscanbeprovided ,be…     

Simulation of nitrogen dynamics and biomass production in winter wheat using the Danish simulation model DAISY

A dynamic simulation model for the soil plant system is described. The model includes a number of main modules, viz., a hydrological model including a submodel for soil water dynamics, a soil temperature model, a soil nitrogen model including a submodel for soil organic matter dynamics, and a crop model including a submodel for nitrogen uptake. The soil part of the model has a one-dimensional vertical structure. The soil profile is divided into layers on the basis of physical and chemical soil characteristics. The simulation model was used to simulate soil nitrogen dynamics and biomass production in winter wheat grown at two locations at various levels of nitrogen fertilization. The simulated results were compared to experimental data including concentration of inorganic nitrogen in soil, crop yield, and nitrogen accumulated in the aboveground part of the crop. Based on this validation it is concluded that the overall performance of the model is satisfactory although some minor adjustments of the model may prove to be necessary.     

聚酯的摩尔质量与机械性能研究——Ⅰ.动态力学性能

应用粘弹谱仪考察了不同摩尔质量的聚酯(PET、PBT、PBT/PET)的动态力学性能,结果表明摩尔质量增大将提高其模量,但亦导致结晶速度变慢,使测得的模量反而比摩尔质量较低的试样小.