High temperature transport kinetics in heteroepitaxial LaFeO3 thin films

Heteroepitaxial LaFeO₃(1 1 0) thin films with a thickness of 150 nm were grown on LaAlO₃(0 0 1) by reactive sputtering in an inverted cylindrical magnetron geometry. Equilibrium conductivity was measured as a function of partial pressure of oxygen at T=1000 °C, and logσ plotted vs. logP(O₂) showed a minimum in conductivity for P(O₂)=10⁻¹¹ atm and a linear response between 10⁻¹⁰ and 1 atm. This linear response makes thin films of LaFeO₃ a promising material for oxygen sensor applications. We have also measured the time response of the film conductivity upon an abrupt change in the partial pressure of ambient oxygen from 10⁻² to 10⁻³ atm, which was determined at 60 s for T=700 °C and <3.5 s at T=1000 °C.     

驻极体声传感器及其储电材料的现状

综述了驻极体声传感器及其储电材料近年来的迅猛发展。传统的FEP(tetrafluoroethylene—hexa—fluoropropylene copolymer)极体电容式声传感器及以铁电聚合物PVDF(poly vinylidene fluoride)家族为芯片的声传感器和超声抉能器仍焕发着青春活力。Si基微型驻极体声传感器的理论和实验研究已经日趋成熟，而用空间电荷型多孔聚合物驻极体压电薄膜为芯片可望研制出新一代声电和电声传感器、压力传感器和驱动器。     

乳化液浓度自动检测配比系统

本文论述了乳化液浓度自动检测配比系统。文章给出了阻容型浓度、液位传感器的原理、结构和测试电路，以及实现乳化液浓度自动检测与自动配比的系统硬件和软件。系统样机通过了型式试验、防爆和工业性试验。研究结构表明，本系统性能优良，达到了煤矿监控产品技术标准，对提高煤机械自动化程度具有重要意义，推广应用前景广阔。     

Reactor modelling for electrochemical processes

This paper presents a relatively straightforward approach to the modelling of electrochemical reactors operated in batch or continuous modes. The models are based on ideal flow assumptions of either well-mixed or plug flow and incorporate reaction rate models based on electrochemical kinetics and mass transport at one electrode. General characteristics of the reactor models are described, particularly with regard to the need for good mass transport in metal recovery applications. An example is given on the use of the model in the recovery of a heavy metal (Cd²⁺) from an acidified solution containing Cd(II) and Fe(III) ions. The reaction rate model is based on experimental data.     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

无基坑轨道衡的研究

本文对无基坑轨道衡的开发与研制,进行了可行性研究。     

十三陵蓄能电站上水库自动监测系统的设计及运行

由于十三陵蓄能电站上水库地处蟒山之巅，所在山体地质条件复杂。施工期埋设了大量的监测仪器，原有人工监测系统效率低、资料分析的同步性差。2002年5月，对其进行了自动化改造，现已有一套符合其特点的自动化监测系统。十三陵上水库水工建筑自动监测系统已正常运行了三年，同时也存在着问题，有待于进一步的探讨和改进。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

一种用于强振环境的转速传感器

该文介绍一种简单、可靠、小巧的转速传感器。它的特点是在强振环境下仍具有很高的可靠,可用于坦克底盘、重型工程机械,燃气轮机组等机械作为转速监测。     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.