胜利原油350～510℃馏分糠醛精制的研究

对胜利原油 350～ 510℃馏分每 4 0℃切割一种馏分进行糠醛精制 ,考察了实验室条件下不同温度、不同醛油比条件下精制对提余油质量和收率的影响。采用醛油比 3× 1∶1,抽提温度在 70～ 95℃ ,可使精制馏分油粘度指数提高 10～ 2 7个单位 ,精制油收率高于 70 %。     

2.0 Mt/a渣油加氢脱硫装置新氢压缩机性能标定

介绍了中国石化茂名分公司 2 .0Mt/a渣油加氢脱硫装置中的 4M80 30 /2 2 2 0 0 BX型新氢压缩机的特点、技术特征及标定情况。采用国际通用标准对压缩机气体组成、容积流量、轴功率、进排气压力和进排气温度等指标进行了测定。标定表明 ,该机组设计方案合理 ,运转平稳 ,性能指标达到设计要求 ,较好的满足了工艺操作的需要     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

连续工作型电子装备战备完好性预计

从战略完好性的实际内涵出发，考虑到装备实际工作中可能处于不同的工作状态，因而其战略完好性模型也应有所有同。对于处于连续工作状态的电子装备，即使工作中发生故障，只要执行下次任务前能修好，就不影响装备的战略完好性。基于此，得出了电子装备处于连续工作状态下的战略完好性预计模型，并在对应的条件下对此模型的得出进行了缜密的推理。     

分子束外延生长液晶光阀用ZnSxSe1-x薄膜的研究

描述了ZnSxSe1-x光盲紫外液晶光阀的结构和工作原理 ,并从器件的电学模型出发 ,着重讨论了整体器件对ZnSxSe1-x光敏层的特殊要求。采用分子束外延技术在ITO导电玻璃上制备了具有 (111)面定向生长结构的ZnSxSe1-x多晶薄膜 ,通过控制反应时的生长参数 ,制备出了符合器件设计要求的光敏层薄膜。室温下 ,该薄膜的紫外 /可见光响应对比度大于10 3 ;响应波长截止边可通过控制薄膜中的Se组分 ,在 (36 0～ 4 10 )nm范围内连续可调 ;薄膜的暗电阻率在 (4 32× 10 9～ 2 0 3×10 11)Ω·m之间 ,并随着晶粒的增大而减小 ;在液晶光阀工作的低频段 (<2 0 0Hz) ,其光 /暗阻抗比在 0 2 2～ 0 36之间。     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

电子衡器特殊故障的分析及处理

因为电子衡器在安装与调试过程中出现的较为特殊的故障，难以找出正确的起因与处理方法，所以介绍了如何保证电子衡器的正常使用和计量准确性的工作体会。     

土壤源热泵取热的实验研究

通过广泛分析国内外对土壤源热泵实验研究的现状,建立了可以模拟多个地区、多种运行工况的土壤源热泵沙箱实验台,并进行了绝热边界工况短期内取热的实验研究。     

天津通信企业IT信息存储支撑平台

天津通信企业IT信息存储支撑平台承载着天津通信关键业务支撑系统和主要的企业信息管理系统．为IT运营管理提供了高效、快速、稳定、安全的数据源，形成统一的存储平台。该平台采用了多系统存储资源集中共享的方式，通过海量数据的异构存储平台数据迁移实现了多系统的整合．达到多系统的数据资源共享。存储的整合为应用提供了可靠的资源保证，数据的整合则消除了信息孤岛，实现了数据共享。     

A probabilistic model for cleavage fracture with a length scale--parameter estimation and predictions of stationary crack experiments

This study presents a large experimental investigation in the transition temperature region on a modified A508 steel. Tests were carried out on single-edge-notch-bend specimens with three different crack depth over specimen width ratios to capture the strong constraint effect on fracture toughness. Three test temperatures were considered, covering a range of 85 °C. All specimens failed by cleavage fracture prior to ductile tearing. A recently proposed probabilistic model for the cumulative failure by cleavage was applied to the comprehensive sets of experimental data. This modified weakest link model incorporates a length scale, which together with a threshold stress reduce the scatter in predicted toughness distributions as well as introduces a fracture toughness threshold value. Model parameters were estimated by a robust procedure, which is crucial in applications of probabilistic models to real structures. The conformity between predicted and experimental toughness distributions, respectively, were notable at all the test temperatures.