用作图法测定R50的理论分析

研究了步、机枪射击密集度试验中弹着点半经的顺序统计量，给出了作图法测定Ｒ_（５０）的理论分析，得到了作图法是测定Ｒ_（５０）的好方法的结论．     

PSD激光直线度测量仪

介绍了采用PSD传感器设计的激光直线度测量的工作原理，以及激光器、光靶和计算机系统的设计。     

一种新的含水率校正方法

从研究流体流动规律出发,结合模拟井实验结果,建立了多参数、非线性的半理论和半实验含水率校正模型,提出了反映两相滑脱效应的滑动比概念,其计算方法物理意义清晰并具有明确的收敛边界。与模拟井实验结果进行对比,使用平方法降低了含水率校正误差。     

计算机存储系统的9位字节单向错误检测码

本文介绍了一种计算机存储系统中的单向错误检测码，系统构成采用９位字节，其中８位数据位，１位校验位，并使用一个单独的附加奇偶校验字节。单向错误检测码有两类，一类每个字包含固定的奇偶校验位；另一类每个字节包含的检验位的构成方式是任意的。     

CNC中插补和轴伺服的微机仿真

本文级出了在ＰＣ机上对一个自己开发ＣＮＣ系统插祉和轴伺服控制进行仿真的结果。它包含按插补原理对直线、圆和渐开线的插补以及对轴伺服控制中的位置环和前馈控制的仿真。轴伺服马达通过一个二阶连续系统模型来仿真，最后得出对伺服进行前馈控制补偿可显著改善系统的输出。     

Voigt线型及其精确快速算法

通过把上半复平面分为４个区，并在每一区利用不同近似，建立了一种精确快速计算Ｖｏｉｇｔ函数、修正的Ｖｏｉｇｔ函数和Ｖｏｉｇｔ函数偏导数的算法，其最大相对误差小于５×１０－４．该算法是Ｌｉｎｅ－ｂｙ－Ｌｉｎｅ大气透过率／辐射强度计算及其相关应用的有效算法．     

球头碗球面加工组合机床设计

根据球面形成原理,利用铣刀和工件的两个圆运动,合成球头碗的不完整内球面。采用组合机床,结构简单,调整、维护方便,主轴弹性卡头便于工件装卸。对零件尺寸、形状和位置误差进行了分析。通过对铣刀和主轴电机的变频调速,找出最佳切削参数,实现了内球面的高效率高精度加工。     

Comments on the shortcomings of predicting the precision of Cavalieri volume estimates based upon assumed measurement functions

It is well known that the estimation of an object's volume by means of serial cross-sections, the so-called Cavalieri method, yields an unbiased estimate. But by itself it provides no means by which to estimate how precise this estimate is unless the shape of the volume is fully known beforehand. This knowledge can only be partially determined from the serial section information that is collected. Methods have been developed that claim to surmount this difficulty by using the serial section data to create a mathematical model of the volume's shape properties. The model then is used to estimate (predict) the precision of the volume estimate (its CE) from the single set of data available. Unfortunately, the theory underlying the model is flawed and so the model itself amounts to no more than an unsubstantiated guess about the shape of the volume. Therefore, the precision of the volume estimates that one obtains from the method is only as good as the model and this cannot be ascertained from the single set of acquired data. In this letter I explain the inadequacies of the modelling method. I suggest that it be used only with caution, if at all. Instead I suggest two alternative ways to predict the CE, one that is based upon a rule-of-thumb approach to the object's shape, and another that is based upon spectral analysis of the measurement function and that is easy to implement with available computer software.     

并行程序设计环境MPICH的应用机理分析

阐述了在PC集群中运用消息传递接口MPICH（Message Passing Interface and Chameleon）进行并行程序设计的基本方法，并以计算圆周率π值的并行算法程序为例，介绍了MPICH中基本例程的功能和调用方法，并行程序设计的关键技术是如何处理好各个进程之间的通信问题，MPICH采用紧迫协议和约定协议来协调各个进程之间的通信，同时也提供了一些阻塞处理函数和非阻塞处理函数，它们能够使进程充分利用系统资源，大大增加用户编程的灵活性。     

测量输入光窗台阶指标的指示表的选择

阐述了对近贴聚焦型微通道板像增强管中输入光窗台阶高度和平整度指标进行测量时，所用指示仪表的选择依据，并详细分析了指示表在检定过程中的误差来源，进一步计算出其合成标准不确定度和扩展不确定度，从而选定可用于测试的指标表。