幂律流体三维脉动流场数值模拟

利用ANSYS软件，模拟了振动诱导单螺杆挤出机熔体输送段中非牛顿幂律流体的三维脉动流场，得到了三维脉动流场的瞬时速度分布及螺槽中物料的流动轨迹。结果表明，在脉动流场作用下，非牛顿流体的瞬时速度响应与在驱动壁面上所施加的正弦形式的脉动驱动形式不同，横螺槽方向的环流中心位置受幂律指数影响，且发生周期性改变。振动的引入使得在相同的时间内，物料的流动路程增加，且可增大物料的平均停留时间，有利于改善混合效果。     

Simulation of transient process in melting section of reciprocating extruder

Plastic injection molding machine that can be classified as reciprocating extruders are among the most widely used machines in industry. However, most studies in the injector design were based on steady state models developed for extruders that involved no reciprocation. This over-simplified model leaves out the most important aspect of reciprocation. The authors of this paper have derived a transient melting model that takes care of the change from the conventional steady extrusion to that of a discontinuous transient process. This paper describes simulations conducted on the derived model to explain observation that cannot be explained by the steady extrusion model in practical experiments. The simulation was conducted by using parameters given in Donovan's experiment [Polym Engng, 11 (1971) 353]. The simulation results are found to qualitatively match with the experimental results. It proves the validity of the model. Simulation has also been conducted with the model on materials that their viscosities are temperature and shear rate dependent. The result has shown that screw rotation speed, screw axial movement speed, barrel thickness, barrel heat capacity, temperature of heater and polymer are factors affecting the melting speed and the transient effects.     

Dynamic reaction inside co‐rotating twin screw extruder. I. Truck tire model material/polypropylene blends

Waste ground rubber tire (WGRT) is a complex composite containing various elastomers, carbon black, zinc oxide, stearic acid, processing oils, and other curatives. Most of the waste ground rubber tire is composed of mainly natural rubber (NR) and styrene butadiene rubber (SBR) in varying proportions. Blending it with other thermoplastic materials is difficult due to the inherent thermodynamic incompatibility. But, the compatibility can be increased by making the reactive sites in WGRT with suitable chemicals under optimum condition of shearing inside a twin screw extruder and it is said to undergo a dynamic reaction inside the extruder. To understand the mechanism of dynamic reaction process of a rubber/polyolefin blend, the blending of a truck tire model material rubber with polyolefin was first tried before it was applied to waste WGRT material. It was observed that the blends of a truck tire model rubber material and PP thermoplastic are physical mixture of two incompatible polymers in which a continuous plastic phase is largely responsible for the tensile properties. The rubber particles are the dispersed phase. The large particle size and the poor adhesion of these rubber particles are believed to be liable for the poor tensile properties. In case of blends of truck tire model material with isotactic polypropylene the tensile properties are found to be lower than that of its PP‐g‐MA counterpart which can be attributed to the reaction of the MA with the carbon black particles. A schematic representation of the possible interactions has been proposed. The effect of addition of compatibilizers such as SEBS and SEBS‐g‐MA has also been studied. The tensile and TGA studies indicate that the polarity of SEBS and SEBS‐g‐MA induces an increase in the performance characteristics for both types of polyolefins but the intensity of this increase is higher in the PP‐g‐MA based blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 106: 3193–3208, 2007     

四螺棱往复螺杆挤出机的研制

介绍了四螺棱往复螺杆挤出机的研制情况；着重叙述了新研发的四螺棱往复螺杆与传统的三螺棱往复螺杆的特性，并作了比较和分析；对四螺棱往复螺杆在设计和加工中的难点及其在工作时的“柔性”特征等进行了阐述。     

销钉机筒挤出机内销钉附近物料流场分析及功率计算

采用当量粘度的方法，基于牛顿流体模型，提出销钉机筒挤出机内销钉附近流场的应力及速度分布数学模型和销钉消耗功率的计算方法。用NR／炭黑混炼胶进行的挤出过程中销钉消耗功率的研究结果表明，实测值与计算值的相对误差只有4％。     

橡胶冷喂料挤出机螺杆参数与机头压力实用数学模型的研究

运用正交回归试验方法，在Φ橡胶冷喂料挤出机实验台上，研究了螺杆主要参数（长径比，螺旋角，螺槽深度，螺杆几何压缩比）及主要挤出工艺、物性参数（螺杆转速、机头口型，胶料种类）对橡胶冷喂料挤出机机头压力的影响。对各实验因素及实验结果做了统计分析，确定了上述各因素对冷喂挤出机机头压力影响的显著因素，得出了机头压力与螺杆及工艺、物性参数之间的定量计算数学模型。     

Extrusion of ultrahigh molecular weight polyethylene under ultrasonic vibration field

The effects of polypropylene (PP) and ultrasonic irradiation on the processing and mechanical properties of ultrahigh molecular weight polyethylene (UHMWPE) are studied. The results show that PP can effectively improve the fluidity and mechanical properties of UHMWPE. The Izod notched impact strength increases from 92 kJ/m² for pure UHMWPE to 109.2 kJ/m² for the blend of UHMWPE with 10 wt % PP. The Young's modulus increases from 528 MPa for pure UHMWPE to 1128 MPa when 25 wt % PP is contained in the blend, and the yield strength also rises when PP is added. The application of ultrasonic vibrations during extrusion can prominently decrease the die pressure and apparent viscosity of the melt, thus increasing the output of extrudate. An appropriate ultrasonic intensity and irradiation time can further promote the mechanical properties, while an overdose of irradiation destroys them. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2628–2632, 2003     

啮合型同向旋转双螺杆挤出机的挤出机理研究进展

论述了啮合型同向旋转双螺杆挤出机挤出机理研究的最新进展,分析了存在的问题和难点,并提出研究发展的方向。     

橡胶冷喂料挤出机喂料装置的性能分析

对橡胶冷喂料加料装置进行了性能分析，通过对自由喂料，旁压辊喂料和螺旋啮合喂料的分析，得出其进料的必要条件及加料胶条的型体要求。     

步进电机闭环控制在挤压机速度系统中的应用

介绍了一种三相混合式步进电机与传统的步进电机系统截然不同的控制方式以及在挤压机速度控制系统中的应用.