The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

胜利油田污水储罐腐蚀防护方法评价

对胜利油田纯粱采油厂A3钢制生产污水（水温约60℃）储罐使用寿命过低的原因进行了实验考察。水质分析数据表明氯离子浓度高（45-48gm）是污水腐蚀性强的主要因素。A3钢在60℃污水中的腐蚀速率，由极化曲线数据计算的值大大高于失重法测定值，敞开系统中失重法测定值又高于密闭系统中测定值，挂片上出现蚀孔，说明储罐中A3钢发生了氧存在下氟离子引起的局部腐蚀（孔蚀）。元素分析结果表明．储罐阴极保护所用的牺牲阳极铝材含铁等元素量超标。牺牲阳极密封不良，在实验污水中7天后电流效率仅为2．92％，失去阴极保护能力。处于实验污水环境中的有涂层保护的A3钢．14天后出现腐蚀极化电流，表明涂层已失去完整性。要提高该采油厂及胜利油田其他采油厂污水储罐的使用寿命，必须改用合格的牺牲阳极和保护涂层材料。图3表2参7。     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

双头螺栓失效分析

与汽车电机装配在一起的双头螺栓在拧紧后不久便发生断裂。采用扫描电镜、化学分析、金相检验等方法对失效件进行了检测，同时又进行了氢脆试验验证。结果表明，螺栓在进行表面酸洗及电镀时，氢向金属内部扩散和富集，当氢浓度达到一定临界值后，促使氢致裂纹的产生和扩展。在外应力的作用下，即出现氢脆现象导致螺栓断裂。     

有杆泵抽油系统可靠性分析

抽油机井有杆果采油装置检泵故障数据的特点在于相邻两次检泵间隔之间的时间并非总是来自同一总体，可能有某种趋势的变化。通过对故障数据的趋势性检验，可验证其对某一随机过程模型的适应性，从而判定某一口井或某一批工况大致相同油井的运行可靠性，实现对生产井运行可靠性的定量评估。还通过实例说明了有杆泵抽油系统检泵故障数据的可靠性分析方法。     

复合材料压缩破坏模式的缺陷敏感性

本文基于弹塑性分叉理论研究单向纤维增强复合材料的压缩破坏模式和压缩强度对缺陷的敏感性问题。对于常见复合材料,所得结论是:无缺陷或者小缺陷情况的破坏模式为倾斜破坏带;大缺陷情况的破坏模式为水平破坏带;形成水平破坏带的压力值小于形成倾斜破坏带的压力。     

"I know, you know": Epistemic egocentrism in children and adults.

This article reviews the evidence and theory pertaining to a form of perspective-taking failure--a difficulty in setting aside the privileged information that one knows to be unavailable to another party. The authors argue that this bias (epistemic egocentrism, or EE) is a general feature of human cognition and has been tapped by 2 independent and largely uncommunicating research traditions: the theory-of-mind tradition in developmental psychology and, with more sensitive probes, the "heuristics and biases" tradition in the psychology of human judgment. This article sets the stage for facilitating communication between these traditions as well as for the recognition of EE's breadth and potential interdisciplinary significance. The authors propose a life-span account and a tentative taxonomy of EE; and they highlight the interdisciplinary significance of EE by discussing its implications for normative ethics. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

φ140mm套管拔套侧钻工艺技术在濮城油田的应用

濮城油田开发后期,因事故导致损坏的井数不断增多,不仅损失了相当一部分储量,而且严重威胁着油田的发展。针对这一问题,应用拔套侧钻工艺技术对有潜能的事故井进行侧钻更新,投产后取得了良好的效果,成为油田增储上产和挖潜剩余油的重要手段,同时也为解决困扰油田发展的难题找到了好的方法。     

锅炉未焊透椭圆接管结构应力数值分析

应用有限元法对未焊透的椭圆接管结构进行了应力数值分析,并应用压力容器分析设计法,对该结构进行了疲劳分析,得出结构因未焊透缺陷导致疲劳破坏。