爆炸箔起爆系统初始电阻对爆发电流和飞片速度影响的数值模拟

研究了电爆炸箔起爆系统起爆回路初始电阻对爆发电流和冲击片雷管飞片速度的影响规律，分析了影响电爆炸箔起爆系统体系的因素，为在可靠发火条件下降低起爆系统体积提供设计参考。     

阻尼式限流器参数的设计选择

本文阐述阻尼式限流器参数设计选择和产品系列规划的依据原则，并结合实例说明实施步骤与方法，以有助于限流器的正确设计与选用。     

单片机在监控同步电动机运行功率因数中的应用

介绍如何利用单片机自动控制同步电动机运行时的功率因数。     

雷电冲击电流测试系统研究

目的 研究雷电冲击电流测试系统，方法 用无感电阻网络分流器测量雷电冲击电流，并进测量重复性、线性度试验和阶跃波响应试验。结果与结论 所研制的无感电阻网络分流器符合国家标准GB/T7626.5-1999和国际电工委员会标准IEC61000-4-5的要求，且可用于KV级脉冲大电流的测量和雷电浪涌（冲击）模拟器短路电流的波形校准。     

超薄氧化层中的中性陷阱对隧穿电流的影响和应变诱导漏电流

用数值分析的方法讨论了中性陷阱对超薄场效应晶体管(MOSFET )隧穿电流的影响.中性陷阱引起势垒的变化在二氧化硅的导带中形成一个方形的势阱.对于不同的势垒变化,计算了电子隧穿氧化层厚度为4nm的超薄金属氧化物半导体结构的电流.结果表明,中性陷阱对隧穿电流的影响不能被忽略,中性陷阱的存在使隧穿电流增加,并且通过这个简单的模型能够理解应变诱导漏电流的产生机制.     

利用星载多波长辐射计观测资料反演大气气溶胶光学厚度

本文提出了一个利用星载多波长辐射计的可见光和近红外通道观测资料反演气溶胶光学厚度的迭代方案。数值试验结果表明，该方案反演气溶胶光学厚度的误差小于10％。将该方案用于分析我国东南沿海上空NOAA－AVHRR观测资料，得到了较为合理的气溶胶光学厚度的空间分布。     

热释电系数的测量方法

描述热释电系数的两种测量方法。其一为电荷积分法，测试系统简单，测量数据准确，且能满足零电场条件下的测量。其二为动态电流法，采用调制热源技术，研究在特定温度条件下热释电材料的动态热释电响应。     

电流模式n阶传输函数的OA-OTA实现

提出了一种新的实现任意 n阶电流模式传输函数的网络结构。该电路仅含运算放大器 (OA)和运算跨导放大器 (OTA)有源器件 ,因而适于全集成。适当设置 OTA的跨导值能实现任意高阶传输函数 ,且传输函数的系数可独立调整。文中推导了滤波器的设计公式 ,并给出了截止频率为 1 0 0 k Hz的三阶巴特沃斯低通滤波器实例 ,PSPICE仿真结果表明所提电路及设计公式是正确的     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014