A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.     

A Stimulation Method to Assess the Contractile Status of the Lumbar Extensors in a Seated Posture

The purpose of present study was to develop and evaluate methods to assess stimulation responses of the lumbar extensors, as part of a longer‐term goal of detecting fatigue during prolonged sitting. Three stimulation frequencies (2, 5, and 8 Hz) were tested in separate stages, which include 3 stimulation trains and 4 sampling blocks. Repeated measures analyses of variance were used to determine whether any significant differences in mean stimulation responses occurred with respect to stimulation frequency, sampling block, and stimulation train. Reliability of measured stimulation responses was assessed within and between sampling blocks using intraclass correlation coefficients. Stimulation frequencies significantly affected the stimulation responses and time‐to‐potentiation differed between the 3 stimulation frequencies; it was highest for 2 Hz stimulation. All 3 stimulation frequencies resulted in excellent reliability within and between sampling blocks. Use of the current protocol at 2 Hz is recommended as appropriate to measure the lumbar extensors status during prolonged sitting.     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。     

智能型电子式变频电动执行器及其应用

针对原有电动执行器只有以低速运行，通过极强的微调才能修正微小偏差这一缺点，提出智能型电动执行器与各种阀体譬合，利用数字化变频技术，改造目前采用模拟技术的电动执行器，使之具有变速运行、动态响应块，调节定位精度高、稳定性好，故障率低、使用寿命长和应用场合广泛的特点。     

数字储频及其性能分析

文章介绍了3种宽带数字储频的基本结构，分析了宽带数字储频的一个重要指标——量化噪声，根据输出信号频谱的杂散电平比较了三种结构的优劣。     

变频调速系统中电动机和变频器选择及问题分析

本文分析了选用标准笼形电动机的容量计算方法、问题分析和选用变频器的型式、容量、注意事项。     

基于射频技术的无刷同步电机励磁电流的检测

无刷同步电机的励磁系统对励磁电流的测量是制约该励磁方式发展的一大障碍。设计了一个射频系统可以用来解决同步电机的励磁电流的测量问题。该系统可以方便地检测到同步电机励磁机的整流二极管的工作状态并且可以动态地显示励磁电流，极大地方便了运行人员做出判断，而且结构简单、方便实用。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。