小型办公网络组网

通过实例,对小型办公网络组网中涉及到的需求设计、网络连接、网络设备、设备连接等进行了论述。     

无篦条可逆锤式破碎机

首先介绍了锤式破碎机的现状及发展前景，主要阐述了无篦条可逆锤式破碎机的工作原理，较详细地介绍了本机的结构特点和性能优点。     

体积-表面淬火中加热温度的自动控制

根据表面-体积淬火奥氏体规范的要求，分析了感应加热过程中温度控制的特点和方式，并介绍了采用红外线光导纤维测温和微机控温技术成功用于体积-表面淬火中透热温度的自动控制。     

TRT入口方管道爆裂原因剖析

介绍了鞍钢7#高炉TRT装置入口方管道爆裂事故经过,进行了原因分析,并提出了解决措施。     

交流变频调速技术在二辊轧机压下系统中的应用

介绍一种采用变频调速技术控制的二辊轧机压下系统。该系统可控制轧机压下系统的速度在工艺要求的范围内无级可调，压下量以数字动态显示，控制准确、操作方便。文中对系统的组成及工作原理作了较详细的介绍。     

全20CrMnTi表面激光重熔的组织与性能研究

本文对激光重熔20CrMnTi材料表明改性层显微组织分布特征、表面硬度分布规律以及残余应力状态作了研究,结果表明,表面改性层由熔融层、相变硬化层及过渡层组成,且材料表面显微硬度得到大幅度提高,表面硬度达到HV841,约提高4倍。硬化层深度约1mm。残余应力测试得出最大残余应力出现在熔凝带中心,表现为压应力。随着离中心距离的增大,残余应力逐步降低,到熔化带边缘,表现为低幅值压应力;而熔池的外边缘应力在热影响区则转变为拉应力状态。     

The Research of ST-OFDM in Physical Layer of IEEE 802.16a

This paper briefly introduces one of the three physical layer implementations of IEEE 802.16a~[1],WirelessMAN-OFDM PHY.Based on the implementation,the combination of Orthogonal Frequency Division Multiplexing(OFDM)and Space-Time Coding(STC)which is briefly called ST-OFDM in IEEE 802.16a,is investigated under thechannel provided in Ref.[2].Especially,this paper is focused on the influence of the optimal decision threshold on the sys-tern Bit-Error-Rate(BER)performance based on unequal probabilities of sources.The simulations show that when Signal-Noise-Ratio(SNR)is low the optimal decision threshold is obviously superior to the usual one;when SNR is high to someextent,such as 10 dB for 4QAM and 16 dB for 16QAM,we can use the usual decision threshold instead of the optimal     

Structural and magnetic properties of Co1+ySnyFe2-2y-xCrxO4 ferrite system

The samples of the series Co_1+ySn_yFe_{2- 2y- x}Cr_xO₄ ferrites with x = 0.0, 0.1, 0.2, 0.3, 0.4, 0.5 and y = 0.05, were prepared by the usual double sintering ceramic technique. The single- phase spinel structure of the samples was confirmed by using X- ray diffractometry technique. The lattice parameter ’a’ with an accuracy of ± 0.002 Å were determined using Bragg peaks of XRD pattern. The lattice parameter ’a’ decreases with concentration, x, which is due to the difference in the ionic radii of Cr³⁺ and Fe³⁺ ions. The X- ray intensity calculations were carried out in order to determine the possible cation distribution amongst tetrahedral (A) and octahedral [B] sites. The X- ray intensity calculations show Cr³⁺ ions occupying B site. The saturation magnetization, σ_s, and magneton number, n_B (the saturation magnetization per formula unit), measured at 300 K determined from high field hysteresis loop technique decrease with increase in concentration, x, suggesting a decrease in ferrimagnetic behaviour. Thermal variation of low field a.c. susceptibility measurements from room temperature to about 800 K exhibits almost normal ferrimagnetic behaviour and the Curie temperature, T_C determined from a.c. susceptibility data decreases with increase in x.

     

An adaptive non‐conforming finite‐element method for Reissner–Mindlin plates

Adaptive algorithms are important tools for efficient finite‐element mesh design. In this paper, an error controlled adaptive mesh‐refining algorithm is proposed for a non‐conforming low‐order finite‐element method for the Reissner–Mindlin plate model. The algorithm is controlled by a reliable and efficient residual‐based a posteriori error estimate, which is robust with respect to the plate's thickness. Numerical evidence for this and the efficiency of the new algorithm is provided in the sense that non‐optimal convergence rates are optimally improved in our numerical experiments. Copyright © 2003 John Wiley & Sons, Ltd.