Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows:

可视化基站发电管理系统

针对以前的发电管理系统或只是数据呈现,提供市电及发电相关数据信息,或只是提供出车轨迹,主要实现对出车的管理,不能全面反应发电全过程且不便于对发电事件进行分析的情况,提出可视化发电管理系统的概念。在简要介绍了LBS系统、动力环境监控系统后,讲述了可视化基站发电管理系统的组成以及通过LBS定位管理、短信互动、实时监测数据等进行系统实现。可视化发电管理系统通过可视化的界面帮助发电管理人员进行管理,直观、便捷。     

Protecting the infrastructure with thermal spray coatings—Technical note

Thermal sprayed aluminum and zinc provide long-term (> 20 years to first maintenance) corrosion control coatings. However, this application is usually more expensive than painting or galvanizing if thermal spraying (metallizing) is not integrated into the design and fabrication phases of new construction and repair projects. Aluminum and zinc metallized coatings are tough enough to withstand fabrication, transportation, and assembly operations. The improved capabilities and productivity of metallizing equipment for aluminum and zinc spraying are a major factor in their current cost competitiveness. The net result is that the cost difference between metallizing, paint, and galvanizing is getting closer every day. Even though the initial application cost of metallizing may be higher, the life cycle cost (LCC) and average equivalent annual costs (AEAC) are lower than paint coating systems. Metallizing LCCs, when properly engineered into the construction schedule, are equal to or less than paint coating LCCs. This article summarizes some metallizing considerations for installing improved corrosion control coating systems in new construction and in maintenance and repair of infrastructure. Editor’s Note: The following constants have been used to convert between English and Metric dimensions: 1ft²-0.0929 m²; 1lb/ft²-4.89 kg/m²; 1 mil=0.025mm. Presented at the 5th National Thermal Spray Conference (NTSC-93), Infrastructure Maintenance and Repair Session, 10 June 1993, Anaheim, CA.     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

变频开关电源Fuzzy-PID控制器的设计

针对感应式变频开关电源在对金属材料进行热处理过程中，负载的等效参数和谐振频率发生变化，而变频电源的输出频率不能及时调整和跟踪的问题，结合PID和Fuzzy控制技术的优点，设计Fuzzy-PID控制器对变频电源进行控制，在大偏差时用Fuzzy控制，在小偏差时用PID调节。Fuzzy-PID控制器以单片机8098为核心，采用SPWM专用芯片SA4828，实现变频开关电源的电压、电流双闭环控制，使变频电源不仅具有较快的动态响应、更小的超调，并且具有较高的稳态精度和频率跟踪控制特性。     

IFR-2000阻燃聚丙烯热性能研究

研究了用无卤膨胀型阻燃剂IFR-2000作阻燃剂的阻燃聚丙烯的热性能和阻燃性能。     

高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

POWER CONSUMPTION WITH ANCHOR MIXERS EFFECT OF BOTTOM CLEARANCE

The effect of bottom clearance on power draw for anchors is investigated. The results suggest that power input decreases as the bottom clearance ratio b/D increases. A new correlation is proposed in which both bottom and wall clearance effects on power input are considered. The dependence of power input on these effects is additive rather than multiplicative. Thus, the total power consumption is the sum of the power inputs generated by the wall and bottom clearance. Power results from 3D-CFD numerical simulations are also presented. These results confirm fairly well the experimental points.