Study on Hot Deformation Cracks of Steel D2 Using Procesing Map

ＳｔｕｄｙｏｎＨｏｔＤｅｆｏｒｍａｔｉｏｎＣｒａｃｋｓｏｆＳｔｅｅｌＤ２ＵｓｉｎｇＰｒｏｃｅｓｉｎｇＭａｐＧａｏＳｈａｎ，ＬｉｕＸｉａｎｇｈｕａ，ＷａｎｇＧｕｏｄｏｎｇＡＢＳＴＲＡＣＴＴｈｅｈｏｔｄｅｆｏｒｍａｔｉｏｎｂｅｈａｖｉｏｒｓｏｆｓｔｅｅｌ...     

铝钛双金属板KR曲线测定

利用宽３００ｍｍ、长／宽＝１的横向ＣＴＴ试样对国产铝钛双金属板做了常规力学性能测定，并按航标测定了ＫＲ曲线，经过柔度法和Ｋ值计算，分别测得了ＫＲｉ和ａｉ数据，确定了临界的ＫＣ值通过性能数据对比，研制的材料达到了进口料的性能要求。     

气流式加速度传感器的敏感机理

介绍了在研制气流式加速度传感器过程中，为对气流式加速度传感器进行建模，作者对气流式加速度传感器的工作机理进行了理论性探讨。在分析过程中以流体力学、传热学和惯性理论为基础并结合实验结果，建立了适合于气流式加速度传感器的气体运动方程和能量方程。同时还讨论了热线测量加速度的方法及根据实验分析了输入加速度对腔体内温度及传感器输出电压的影响，从而为进一步研究一系列气流式传感器的工作机理提供了方法。     

钢／铝合金液固相复合工艺的研究

通过正交试验研究了各工艺量数以钢／铝合金液固相复合性能的影响，最佳工艺条件为铝合金液体温度７９０℃，钢板表面处理为酸洗＋钢刷＋５％的氟钛酸钾助焊剂，复合压力为３９．２ＭＰａ，组织观察表面界面脆性化合物的形成是导致结合强度降低的一个重要因素。     

Equipment for Testing Sheet Structural Materials under Biaxial Tension. Part 2. Testing by Biaxial Loading in the Plane of the Sheet

We analyze specific features of the design of equipment used for mechanical testing of sheet structural materials under the conditions of biaxial static, cyclic, or dynamic loading. We propose original solutions of the problems related to the fatigue testing of crosslike specimens performed without using complex hydraulic systems and their dynamic testing carried out by using very simple testing machines for uniaxial tension–compression.     

���ɹų����ˮ����Ȫ��Ȼ�������о�

本文结合实际资料,对内蒙古赤峰热水镇温泉天然气的地球化学特征进行了分析和研究。结果表明:上述天然气由多种成因气体组合而成。其中He属壳源放射性成因,CO_2属有机成因,CH_4属无机合成,N_2属大气成因。     

连铸铝镇静钢的钢水准备

在连铸生产铝镇静钢时,水口絮流一直是困扰工程技术人员的一个难题.从絮流的原因入手,分析了Al2O3生成的控制.并介绍了几种钢水钙化的方法,从中比较出用复合造渣材料来解决浇铸铝镇静钢的优点.     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.