Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

用EGS4分析9MeV行波直线加速器屏蔽系统

采用了国际上广泛使用的ＭｏｎｔｅＣａｒｌｏ模拟计算程序ＥＧＳ４对海关集装箱检测系统用加速器屏蔽系统进行了辐射模拟分析，与实际测试数据进行分析、比较，解释了特殊剂量分布的原因，提出了系统改进的参考方案。     

Characteristics and classification of high-current fault arcs on distribution systems

When a fault occurs on transmission or distribution systems due to lightning or overvoltage, often an arc discharge occurs at the fault point. The arc discharge, which is caused by a fault current, has a high current, high temperature, strong light emission, etc., thus it sometimes causes heavy damages to electric power equipment. The arc discharge is influenced by the conditions around the arcs, i.e., gas, insulation materials, gap length, weather, etc. Also, the arc voltage along the arc column indicates the characteristics of the arc. If the voltage waveforms of the arcs caused by the fault on transmission or distribution systems are classified, it is possible to find the location and the equipment where the fault occurred. In this paper, the arc voltage data in 6-kV class XLPE cables and 6-kV class overhead lines are analyzed and an artificial neural network method is applied to classify the arc voltage waveforms. The results obtained from the six artificial neural networks developed show that the artificial neural network method is effective for classification of arc voltage waveforms if adequate input parameters are selected.     

应用系统工程原理 促进炼铁技术进步

应用系统工程原理,从铁前抓起,不断进行技术改造,使焦化、烧结、炼铁工艺及设备系统不断优化,从而确保了300m~3高炉的强化冶炼。     

浅论建设项目投资控制的重点

建设项目控制的重点应放在投资决策和设计阶段中,否则会造成巨大的损失。这不仅需要人们改革组织结构和管理体制,更需要从根本上转变思想观念。     

Dynamic analysis of the NPP pressure sensor system

The aim of the work was to develop on-line methods of control and diagnostics of pressure sensors at a NPP. The analysis was carried out along two lines:

1. i) The detection system including the sensor itself was modeled theoretically to obtain and study its transfer function, and to establish correspondence between the spectral characteristics of the pressure signal.

2. ii) The numerical processing of the signal using the AR technique to reconstruct the transfer function and evaluate the system's response, to a step impulse, as well as the spectral analysis. The hydraulic model presented indicate that the spectral lines observed at 10 Hz are due to longitu-dinal oscillations of water in the system branches, while the response time of the detection system is effectively the time of signal retardation in the porous ceramic diaphragms of the δ-cell of the sensor itself.

     

A calibration method for the energy-integrating function in photovoltaic system monitoring

Solar radiation has an irregularly varying factor due to a basic day and night cycle and climatic conditions. For such conditions a data sampling interval is important to ensure the accuracy of energy monitoring in a photovoltaic system. While treating a system monitoring equipment as a black box. the author has developed the method of calibrating an energy-integrating function. At first for various input waveforms, the relationship between sampling intervals and quasi-integration outputs have been examined by trapezoidal rule. In the numerical simulation the phases of the sampling clock also are considered Then it is concluded that a sampling interval can be inspected through outside observation only by using a rectangular single pulse. By applying the pulse to the energy-integrating process, two kinds of integrated outputs can be obtained for different sampling phases. The calculated difference between both outputs can uniquely give the sampling interval being inspected. Conditions to ensure measuring accuracy are discussed and the validity of this method has been demonstrated experimentally. Practical calibrating procedures also are proposed for the integrating function of PV system monitoring.     

EXTENSION OF THE RELATIONAL DATABASE AND ITS ALGEBRA WITH ROUGH SET TECHNIQUES

This paper describes a database model based on the original rough sets theory. Its rough relations permit the representation of a rough set of tuples not definable in terms of the elementary classes, except through use of lower and upper approximations. The rough relational database model also incorporates indiscernibility in the representation and in all the operators of the rough relational algebra. This indiscernibility is based strictly on equivalence classes which must be defined for every attribute domain. There are several obvious applications for which the rough relational database model can more accurately model an enterprise than does the standard relational model. These include systems involving ambiguous, imprecise, or uncertain data. Retrieval over mismatched domains caused by the merging of one or more applications can be facilitated by the use of indiscernibility, and naive system users can achieve greater recall with the rough relational database. In addition, applications inherently “rough” could be more easily implemented and maintained in the rough relational database.