纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

POCV-200/31.5型液控单向阀

介绍了一种用于液压支架大流量、快速移架系统中的POCV——200／31．5型液控单向阀的工作原理和结构特点。分析了该阀的性能，并指出了其推广应用前景。     

MG—375/750采煤机液压系统的污染控制

介绍了MG— 375 75 0采煤机液压系统污染危害的种类及控制方法 ,并收到了良好效果     

Stability of Equilibria in a Four-dimensional Nonlinear Model of a Hydraulic Servomechanism

Starting from plysical laws a four-dimensional nonlinear model for mecano-hydraulic servomechanisms is deduced. The stability of its equilibria is analysed using a theorem of Lyapunov and Malkin to handle the critical case due to the presence of zero in the spectrum of the matrix of the linear part around equilibria. Stability diagrams are drawn and simulation results are presented through phase diagrams.     

土工合成材料在辽宁省水利工程中应用效益分析

截止2003年辽宁省水利工程中应用土工合成材料已达1450万多m^2，尤其在河道护岸、堤(坝)护坡、防渗工程上这种新型工程材料得到了广泛应用。结合辽宁省水利工程上应用的实际，对其效益进行了分析，分析结果表明：采用土工织物软体排护岸比传统柴排护岸节省投资35％～80％；堤坝护坡采用土工织物滤层比传统砂砾料滤层节省投资30％以上；土工膜防渗可比粘土防渗节省投资30％～50％。同时还取得了保护生态平衡、节省能源、促进化纤工业发展等十分显的社会效益。     

高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

水力压裂净压力拟合分析解释技术研究与应用

基于三维裂缝延伸模拟模型的水力压裂净压力拟合分析解释技术,提出了净压力拟合分析解释的一般步骤及理论方法,研究了现场监测净压力的计算方法,并介绍了其在现场施工中的应用情况。该技术可以帮助认识地层参数和压裂参数,提高压裂施工成功率和有效率。     

氧气顶吹转炉溅渣护炉试验研究

采用水力模型研究方法 ,针对马钢 2 0t转炉进行溅渣护炉冷态模拟试验 ,得出最佳工艺参数为 :枪位 1680mm ,氮气流量为 110 0 0m3/h ,大流渣量 ,渣粘度适中。此外 ,在满足炼钢生产的条件下 ,采用夹角为 13°的喷头溅渣效果好     

ETR Ⅱ-30调速器液压控制系统

ETRⅠ-30调速器是瑞士爱舍维斯工厂生产的具有PID调节规律的电液调速器。本文对其液压控制系统作了较详细的介绍,供有关人员参考。     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.