Stress Heterogeneity Effect on the Strength of Silicon Nitride

The experiments reported in this paper demonstrate the causes of the failure of monolithic ceramics. The specimens are made of silicon nitride and tested at room temperature. The stress field within the specimen is different for each of four series of tests that have been conducted. Fractographic observations have also been made to identify the causes of the failures. A size effect analysis is performed.     

脆断事故的原因分析和预防措施

分析高强度材料和大型工程结构元件发生低应力脆性断裂的原因及条件，指出传统强度设计理论的局限性，从设计和工艺上提出防止发生低应力脆断事故的具体措施，给使用高强度材料和设计大型工程结构元件时提供参考。     

25mm厚钢板产生层间撕裂的原因和防治

层间撕裂并非是厚板独有的质量问题 ,结合工程实例 ,分析 2 5mm厚低合金钢板产生层间撕裂的原因。通过对钢材的超声波探伤检测、化学成分分析和Z向性能检测 ,指出层间撕裂主要与节点设计不当和钢材内非金属夹杂物偏析、分层有关 ,并提出了预防措施。对产生裂纹的构件视严重情况提出了不同的修补处理方法     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

具有初曲率板弯曲的边界元分析

由于具有初曲率板弯曲问题的控制微分方程较复杂，直接求解原问题基本解推导边界积分方程较为困难。本文通过引入等效荷载，将此问题的控制微分方程化成与普通板弯曲基本方程形式相同的微分方程，利用一般求解板弯曲问题的边界元法迭代求解，建立了分析具有初曲率板弯曲问题的边界元法。算例表明本方法理论准确、精度良好。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。     

Rene′95粉末合金喷丸强化研究

研究了Ｒｅｎｅ′９５热等静压粉末高温合金喷丸后的残余应力场、组织结构、致密度及其与疲劳性能的关系。结果指出，喷丸强化能够有效地提高合金高周和低周疲劳强度。     

垂直平行束状孔爆破模型试验与分析

垂直平行密集束状孔落矿有底柱崩落法是一种新的采矿方法。通过爆破模型试验，测试爆破应力，观察分析爆破效果，探求最佳布孔形式，选择最优爆破孔网参数。试验结果表明：用平行束状孔取代扇形落矿，改善了爆破效果，简化了采场结构，减少了采切工程量。