焦炉集气管压力系统内模控制器设计

针对焦炉集气管压力控制系统具有强干扰、非线性时变、滞后等特点,设计基于最小二乘支持向量机的内模控制（Least Squares Support Vector Machines-Internal Model Control,简称LSSVM-IMC）与非线性PID控制（Nonlinear PID control简称NCPID）相结合的复合切换控制策略。将系统不同工况分开考虑,根据不同工况采用不同的控制算法。在正常工况下采用LSSVM-IMC算法对系统进行细调,以抑制未知干扰的影响,提高控制精度;在非正常工况下,采用NC-PID算法对系统进行粗调,使得系统在短暂时间内快速脱离高压或低压状态。仿真结果表明该控制策略不仅提高了系统的快速调节能力和稳态精度,而且增强了系统的鲁棒性。     

The relation between the parabolic rate constants for the internal oxidation of binary alloys in terms of weight gain or thickness

A calculation of the parabolic rate law for internal oxidation in binary alloys expressed in terms of weight gain shows that its dependence on the concentration of the most-reactive component is different from that predicted by the classical Wagner treatment for the rate constant expressed in terms of thickness of the internal oxidation zone. It is shown that the ratio between the two rate constants for a given system is a very sensitive function of the concentration of the reactive element in the alloy.     

半潜式钻井平台内波工况定位能力

采用MOSES软件建立动力定位半潜式钻井平台分析模型,在时域内模拟平台在钻井作业过程中遭遇内波作用的耦合动力特性,分析平台在不同流速内波作用下的定位能力,并对动力定位系统的关键因素进行敏感性分析。研究结果显示：在同等环境载荷强度下,平台在船宽方向出现最大偏移;当内波流速小于1.0 m/s时,平台可基本满足钻井作业的定位要求,而当内波流速达2.0 m/s时,平台出现大幅值的水平偏移和倾角,需要解脱隔水管系统;提升推进器推力和增加推力敏感因子都有助于提升平台的抗内波能力,但都无法明显减小平台的水平偏移。因此,在遭遇高流速内波作用时,推荐平台撤离或调整船体首向。     

海洋温差能发电冷水管涡激振动性能

以海洋温差能发电（Ocean Thermal Energy Conversion,OTEC）平台的冷水管为研究对象,根据结构方程和尾流振子方程建立冷水管流固耦合模型,采用有限元方法和 法对冷水管涡激振动（Vortex-Induced Vibration,VIV）进行时域分析,并在MATLAB软件中开发相应的求解程序。针对冷水管所面临的复杂工况,分别研究外部流场、内部流场、长径比和压载质量等因素对VIV产生的影响。结果表明：随着外流流速和长径比的增大,冷水管横流向VIV模态和振动幅值也发生相应改变,振动强度呈现波动上升;在不发生动态失稳的情况下,内流流速的增加可有效减小冷水管横流向振动幅值,压载质量可大幅减小冷水管自由端的振动位移。     

The effect of washing process on the cracking of ZrO2 microspheres by internal gelation

ZrO₂ microspheres are widely used as a simulant of UO₂ in the development of nuclear fuel. However, the cracking of ZrO₂ microspheres prepared by internal gelation is still a challenge during drying and sintering processes. To address this issue, we designed and optimized the washing process for obtaining crack-free ZrO₂ microspheres. Through thermogravimetric, infrared, Raman, BET, and SEM analysis, it is shown that the cracking of the microspheres is mainly related to the pores in microspheres. The washing solvent with low surface tension is used to reduce the effect of capillary force on pore shrinkage. Therefore, the optimal washing process was designed as trichloroethylene (TCE)—0.5 M NH₃.H₂O—Propylene glycol methyl ether (PM) and gel microspheres with a high specific surface area of 315.3 m²/g and pore volume of 0.4125 cm³/g were obtained. The characterizations also further showed that when the microspheres were dried and sintered, the water vapor and the decomposition gas of organic matter were completely released from the pores in the microspheres. Our new washing process could be directly extended for preparing crack-free ceramic microspheres by internal gelation.     

基于多尺度数学形态学和高低频能量比值的海上风电场内部瞬态过电压特征分析

目前,海上风电场集电系统因电气设备频繁操作或故障所引起的高频瞬态过电压尤为严重。为识别不同类型下海上风电场内部过电压的瞬态特性,该文首先提出一种多尺度数学形态学信号特征提取方法,构建形态学结构元素新算子,运用多尺度数学形态分解方法提取瞬态过电压的高低频成分,构建适用于识别海上风电场内部瞬态过电压类型的时域特征量。再基于所构造的高频特征量和高低频能量比值识别特征量,结合支持向量机分类器模型对典型的内部瞬态过电压分类识别。仿真和试验研究表明,所提出的数学形态学算法相对于传统的小波算法,构造的特征量区分度更明显,可以准确地识别过电压类型,为海上风电场变电站电气设备的电压保护整定和绝缘配合奠定基础。     

Numerical Simulation of Internal Oxidation of Steels during Annealing Treatments

This paper presents a new model for simultaneous diffusion and precipitation of chemical elements in metallic matrices, a scheme for its numerical solution, and several applications to problems of internal oxidation. The model basically stands as an extension of the classical Wagner model for internal oxidation of steels, but is more much general in that it allows for an arbitrary number of diffusing chemical elements, an arbitrary number of precipitate phases with arbitrary compositions, dependence of diffusion coefficients and solubility products upon (time-dependent) temperature, etc., thus allowing for a much broader range of applications. As a counterpart, it is generally impossible to solve the complex, non-linear equations of the model analytically, but this can be done numerically. The simple but efficient numerical scheme proposed is based on explicit 1D finite differences. Experience has shown that this scheme, in spite of its rusticity and the restrictions it imposes on the time-step, is more efficient than more elaborate strategies based on the finite-element method. The applications presented are concerned with internal oxidation of steels during annealing processes. The model and associated numerical scheme allow for evaluation of the amounts of the various oxide precipitates in the external layer of the sheet. This opens the way, through numerical parametric studies of the influence of the process parameters and the chemical composition, to the improvement of existing treatments and the development of new steel grades.     

铝双晶晶界的内耗峰

用受迫振动法测量了夹角为60°和129.5°的铝双晶的内耗,都观测到一个温度内耗峰,峰巅温度是200℃左右(频率1Hz)激活能为0.88eV对于这个内耗峰的机制做了初步解释。     

渐开线零齿差机构啮合原理与强度条件

零齿差机构的突出问题是齿轮的干涉与强度。在导出避免干涉的条件后，建立新的强度公式，给出各项检验指标，并提出切齿过程中保证精度的具体措施。     

Al2O3/Cu复合材料的内氧化制备及性能研究

采用高能球磨制备出亚稳态的Cu-1%Al（质量分数）合金粉,再将Cu2O粉与其一起进行高能球磨,然后将复合粉末压坯在N2保护炉中同时进行氧化和烧结,制备出Al2O3/Cu复合材料。分析了分别采用湿法球磨和干法球磨时的合金化效果,讨论了模压压力对材料性能的影响。结果表明,对于Cu-Al混合粉来说,采用湿法球磨容易产生分层,采用干法球磨具有良好的合金化效果;在本试验条件下,750MPa为最佳的模压压力,但烧结后材料的电导率还是偏低,因此有必要进行后续的处理来进一步提高材料的性能。