Pervaporation performance analysis and prediction—using a hybrid solution-diffusion and pore-flow model

A hybrid mathematic model for pervaporation is proposed which incorporates the concepts of solution-diffusion model and pore model. The model allows performance prediction as well as the establishment of the internal concentration and pressure profiles within the membrane. The model parameters specific to the particular membrane and mixture system are determined using liquid sorption and pervaporation experimental data. The model is experimentally examined using ethanol–water mixtures and poly(dimethyl siloxane)–poly(vinyldiene fluoride) (PDMS–PVDF) composite membranes. The characteristics of flux and separation factor predicted using the model are in fair agreement with the experimental data under various feed concentrations and downstream pressures for different membrane arrangements, including single-layer, reverse single-layer and double-layer PDMS–PVDF composite membranes. Internal profiles of pressure, concentration and component mole fraction can be established using the model. Concentration polarization phenomena for ethanol and water are located at membrane interfaces and vapor–liquid interfaces, respectively. Performances of several different membrane designs are compared using the model.     

Influence of the composition of the binder and the carbonation on the zeta potential values of hardened cementitious materials

Electroosmotic experiments have been carried out on eight different mixes of hardened cementitious matrixes including concrete, mortar and pastes, different types of binders, carbonated and non-carbonated specimens and different test conditions. From these trials, the zeta potential values have been determined and the optimum experimental parameters and devices have been established. In addition, the influence of the composition of the binder on the zeta potential has been quantified indicating that higher amounts of Al₂O₃ in the binder lead to higher positive values of zeta potential, while the SiO₂ acts just on the opposite side. This has been explained in terms of the different i.e.p. (isoelectric point) for both oxides. Concerning the influence of carbonation, it increases the absolute value of the zeta potential toward more negative values; this behaviour has been attributed to the influence of the specifically adsorbed Ca²⁺ in the negative sites of the surface in the non-carbonated samples.     

Thermodynamic assessment of MCl–YCl3 (M=Na,K, Rb,Cs) systems

Thermodynamic properties and phase diagrams of the MCl–YCl₃ (M=Na, K, Rb, Cs) systems were reassessed by using the CALPHAD method with the latest phase diagram data. A two-sublattice ionic solution model (M⁺)_P(Cl⁻, ${\mathrm{YCL}}_6^{3-}$, YCl₃)_Q reflecting the ionic behavior of the components was adopted to describe the liquid phase in the systems. A new set of optimized model parameters was found, and the calculated phase diagrams and enthalpies of mixing have good agreement with experimental data. The calculated liquidus near to YCl₃ side agrees much better with experimental data compared with previous work. In consideration of high and low temperature modifications as well as stability of intermediate compounds, Gibbs energies of formation of these compounds evaluated in the present work are more reasonable.     

高效防腐中温磷化液LC-1的制备及性能

制备了一种含Zn2+、Mn2+、N i2+三系离子的LC-1磷化液,通过硫酸铜点滴、氯化钠浸蚀、SEM等手段对磷化膜进行了测试,测定了磷化温度、磷化时间对膜层耐蚀性的影响。结果表明,在磷化温度大于65℃,磷化时间大于10 m in的条件下,所形成的磷化膜结晶均匀、致密、黑褐色,耐蚀性良好。LC-1三系磷化液可适用于大批量钢铁工件的磷化生产。     

Influences of zinc oxide and an organic additive on the electrochemical behavior of pure aluminum in an alkaline solution

The corrosion behavior of pure aluminum in inhibited and uninhibited 4 MKOH was investigated by means of hydrogen collection, polarization curve measurement and electrochemical impedance spectroscopy (EIS). The results showed that the corrosion of pure aluminum was greatly inhibited by the addition of ZnO and dimethyl amine epoxy propane (designated as DE). EIS and EDAX analyses revealed that ZnO produces its effect by depositing on the aluminum surface, which increases the overpotential of hydrogen evolution. It was also found that the addition of DE could greatly improve the deposition of zinc layers.     

酸性镀锡液的新进展

从近几年美国发明专利的角度扼要综述酸性镀锡液的新进展。说明酸性镀锡液由氟硼酸盐型发展为烷基磺酸盐型的改进过程。列出参考文献９篇。     

小波变换在求解重力测定反问题中的应用

针对重力测定反问题,提出将其离散为线性不适定问题,利用小波变换方法进行数值求解.该方法将小波变换和正则化方法相结合,选取小波函数作为一组基底,将原不适定问题转化为粗子空间上的适定问题,并给出选取粗子空间基的方法.通过数值模拟已有方法和小波变换方法求解结果的比较,表明了小波变换方法的可行性和有效性.     

FEM analyses for influences of stress corrosion and pressure solution on THM coupling in dual-porosity rock mass

With the models of stress corrosion and pressure solution, by Yasuhara et al., two computation conditions were designed for a hypothetical nuclear waste repository in an unsaturated dual-porosity rock mass: (i) the fracture apertures are changed with the stress corrosion and pressure solution (the porosity of rock matrix is also a function of stress); (ii) the fracture apertures and the porosity of rock matrix are constants. Then the corresponding two-dimensional FEM analyses for the coupled thermohydro-mec...     

世界溶液丁苯橡胶的主要技术进展

评述了溶液丁苯橡胶的技术现状和主要技术进展。介绍了新型锡锂引发剂和用其制备的溶液丁苯橡胶的性能特点，特别是其突出的滚动阻力特性和在不损失湿牵引性下的优异耐磨性。分析了世界，特别是美国、欧洲和日本的溶液丁苯橡胶的需求现状及发展趋势。