A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.     

注射成形Fe-50%Ni软磁合金的研究

Fe-50 %Ni合金是一种典型的高磁导率和低矫顽力的软磁材料,有着广阔的应用前景.本次实验采用注射成形方法制取Fe-50 %Ni,研究了在注射成形工艺中烧结工艺对最终产品性能及微观组织的影响,并分析了影响产品磁性能的一些主要因素.实验表明,烧结温度的提高和烧结时间的延长能够较好改善产品的力学性能;密度是影响产品磁性能的主要因素,杂质(主要指(C、O、N)的含量和晶粒尺寸对剩磁、磁导率和矫顽力也有较大的影响;通过注射成形方法制取的Fe-50 %Ni,其性能要优于采用传统粉末冶金方法制造的Fe-50 %Ni.     

Co- and Ni-exchanged ferrierite: The contribution of synchrotron X-ray diffraction data to siting of TMIs

High-silica zeolites exchanged with transition metal ions (TMIs) are the subject of great interest for their unusual catalytic activity and selectivity. Structural information like coordination and accessibility of TMIs in zeolites are important factors for understanding their catalytic activity. Siting of TMIs in zeolites is typically obtained by spectroscopic (EXAFS, EPR, UV–vis and IR) and computational methods, as in the case of Co-ferrierite. However, some controversy exists in the literature concerning the model for incorporation of bare Co ions in ferrierite. We show here that the results of our synchrotron X-ray powder diffraction studies on Co- and Ni-exchanged ferrierite (Si/Al = 8.5) are in a good agreement with the model of Co siting based on an indirect spectroscopic approach and help to validate this model. By direct structural evidences, a possible explanation for the larger catalytic activity of Co sites in the main channels of ferrierite can be inferred. A combination of data from in situ XRD continuous monitoring of the Co ion migration during calcination and crystal-chemical considerations allows to device a strategy for the design of optimised co-cations containing Co-ferrierite catalysts.     

国有公路运输企业改革创效的现实选择

通过对公路运输企业经营实践的考察 ,介绍了国有公路运输企业改革创效的一些现实选择 ,以供运输公司经营借鉴 ,从而摆脱困境 ,取得良好业绩     

Formation and electronic structure of interface

In the present work the formation of the interface between polycrystalline silver and thin films of titanium oxide was studied with photoelectron spectroscopy (XPS, UPS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Titanium oxide was deposited stepwise on 100 nm thick silver films by reactive magnetron sputtering allowing to study the evolution of the interface formation process. The process involves two steps: formation of thin layer of silver oxide and subsequent growth of the TiO₂ film. For better understanding of the silver oxidation process, pure silver films were exposed to a low temperature Ar/O plasma for different time intervals providing a possibility to investigate early stages of the oxide film growth.     

微量元素对管道焊缝性能的改善

在焊条中添加微量元素Ce、Y、Ca、Ba和Zr，有利于改善石油天然气管道焊缝的金属性能，俄罗斯专家对此做了一系列实验和研究。结果表明添加微量元素有利于提高焊缝金属平面应变断裂韧性KIC，提高裂纹张开位移δc，减小裂纹扩展速率dα／dN改善焊缝金属的组织结构。通过大量的试验和研究，俄罗斯焊接学者确定了焊缝中微量元素的最佳含量，并建立了相关参数的数学模型。     

Estimation for the number of components in a mixture model using stepwise split-and-merge EM algorithm

The main difficulty with EM algorithm for mixture model concerns the number of components, say g. This is the question of model selection, and the EM algorithm itself could not estimate g. On the contrary, the algorithm requires g to be specified before the remaining parameters can be estimated. To solve this problem, a new algorithm, which is called stepwise split-and-merge EM (SSMEM) algorithm, is proposed. The SSMEM algorithm alternately splits and merges components, estimating g and other parameters of components simultaneously. Also, two novel criteria are introduced to efficiently select the components for split or merge. Experimental results on simulated and real data demonstrate the effectivity of the proposed algorithm.     

直流法测量钯氢化物电极电阻时的阻值偏移

讨论了直流法在线测量钯氢化物电极电阻时的电化学效应，计算了电解液的共导、测量电流与电解电流引起的浓差电池效应以及电极作为集流体引起的电阻贡献。结果表明：当电极具有高的长度与半径比值、粗糙的表面、高的溶液电导以及大的电解电流时容易引起显著的附加电阻。     

磷矿中七种金属元素的光谱法测定

研究了磷矿样品中7种金属元素锰、钴、镍，锌、铬、钼及铋的分析方法，选择了灵敏度高干扰少的谱线，绘制出工作曲线，对样品进行了科学处理，不必进行化学分离即可对七种元素同时测定，经合成样分析、回收实验及样品测定，证明此方法精确可靠，其回收率在98％-102％之间。