湿敏半导体材料电导率计算方法的研究

结合修正了的耗尽层理论和多孔湿敏半导体的特点，本文提出了一个简单的物理模型作为ｎ型湿敏半导体特征的一级近似。描述了多孔湿敏半导体的导电机理，并给出了湿度与宏观电导率的关系。     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

苎麻阳离子改性的研究（三）：改性苎麻的染色机理

采用上染速率，等温吸附模型，Ｚｅｔａ电位、染料与纤维的结合力等方法从理论上研究了改性苎麻的染色机理，苎麻改性后，纤维表面的Ｚｅｔａ电位由原来的－４２ｍＶ提高到－１８ｍＶ，正电性显著增加，提高了阴离子染料对改性苎麻的亲和力，上染率高，节约染料。     

管内机器人研究中的几项新技术

介绍了我们研制的管内机器人中应用的具有创新性的三项技术：１．轮式全主动新型行走机构；２．内壁环带视觉装置；３．新型离心喷涂器。     

徐淮地区煤矿井筒破裂机理研究

从徐淮地区井筒破裂的特点出发，分析引起井壁破裂的根本原因，据此提出井筒的破裂机理，为选择防治井筒破裂的方法提供依据     

夏季面漆起泡的预防

面漆漆膜在夏季潮湿天气下成膜后3—5天，漆膜表面易形成米粒状的漆泡，针对漆泡的现象，寻找其形成的机理，根据起泡的机理采取预防面漆起泡的措施。     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

一维弹道修正模块设计与仿真

简要介绍了一种用于维弹道修正引信的执行机构。通过数学模型，结合MDT三机械设计软件和Working Model动力学仿真软件，对机构的受力情况和工作过程进行了数字仿真和系统分析，并通过对飞行弹道的模拟，得出了一维时间控制射程修正规律。     

浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果     

Experimental Study on the Effect of Steel-fibre in Conerete Thick Cap

The effect of steel fibre used in concrete was systematically analyzed by model testing of 30 2-pile thick caps of steel-fibre reinforced concrete, in which the model scale was 1：5. The experiment system composed of a loading device, strain measurement system and a data-acquisition system was used, also an electromechanic centigrade scale, a lens and a Y J-25 static resistance strainometer were used.The experimental results show that the volumetric rate of steel fibre and draw ratio have an important influence on its load-bearing capacity. The incorporation of steel fibre can effectively improve the extension and reduce the thickness of the caps.