一种新的修正恒模算法

阐述了恒模算法(CMA)、修正恒模算法(MCMA)和判决引导(DD)算法的基本原理。针对CMA和MCMA收敛速度慢,固定步长条件下收敛速度和剩余误差之间存在矛盾的缺陷,在分析CMA误差特性的基础上,利用DD算法误差函数的模值和判决器输出构造新的误差函数,提出了一种新的变步长MCMA。新算法在加快收敛速度的同时保持小的剩余误差。仿真结果表明,新算法比CMA和MCMA收敛速度快,均衡输出剩余码间干扰(ISI)小而且能克服相位偏移,具有很好的实用性。     

浅议进一步发挥军事代表在武器装备全寿命费用管理中的作用

阐述了军事代表参与武器装备全寿命费用管理的现状和作用,提出了提高军事代表费用管理参与率的措施.     

20 kg铝锭铸造机铸模改进方案探讨

为了适应火车全面调速后货运高度的要求，提出了有效的铸模改进方案。对铸模改造前后的使用寿命进行了分析。通过改造达到了降低铝锭垛高的目的，同时延长了铸模的使用寿命。     

Protecting the infrastructure with thermal spray coatings—Technical note

Thermal sprayed aluminum and zinc provide long-term (> 20 years to first maintenance) corrosion control coatings. However, this application is usually more expensive than painting or galvanizing if thermal spraying (metallizing) is not integrated into the design and fabrication phases of new construction and repair projects. Aluminum and zinc metallized coatings are tough enough to withstand fabrication, transportation, and assembly operations. The improved capabilities and productivity of metallizing equipment for aluminum and zinc spraying are a major factor in their current cost competitiveness. The net result is that the cost difference between metallizing, paint, and galvanizing is getting closer every day. Even though the initial application cost of metallizing may be higher, the life cycle cost (LCC) and average equivalent annual costs (AEAC) are lower than paint coating systems. Metallizing LCCs, when properly engineered into the construction schedule, are equal to or less than paint coating LCCs. This article summarizes some metallizing considerations for installing improved corrosion control coating systems in new construction and in maintenance and repair of infrastructure. Editor’s Note: The following constants have been used to convert between English and Metric dimensions: 1ft²-0.0929 m²; 1lb/ft²-4.89 kg/m²; 1 mil=0.025mm. Presented at the 5th National Thermal Spray Conference (NTSC-93), Infrastructure Maintenance and Repair Session, 10 June 1993, Anaheim, CA.     

High-speed milling of titanium alloys using binderless CBN tools

The performance of conventional tools is poor when used to machine titanium alloys. In this paper, a new tool material, which is binderless cubic boron nitride (BCBN), is used for high-speed milling of a widely used titanium alloy Ti–6Al–4V. The performance and the wear mechanism of the BCBN tool have been investigated when slot milling the titanium alloy in terms of cutting forces, tool life and wear mechanism. This type of tool manifests longer tool life at high cutting speeds. Observations based on the SEM and EDX suggest that adhesion of workpiece and attrition are the main wear mechanisms of the BCBN tool when used in high-speed milling of Ti–6Al–4V.     

混凝土小砌块与普通砖混住宅楼造价分析

指出混凝土小型空心砌块是一种节能型的新型墙体材料。本文从经济角度对该种材料和粘土砖材料进行了实例分析、比较,得出了这种新型材料值得推广使用的结论。     

High cycle fatigue behaviour of Ti–6Al–4V alloy at elevated temperatures

High cycle fatigue behaviour of Ti–6Al–4V alloy was studied at 623 K and 723 K. Fatigue strength decreased at elevated temperatures compared with at ambient temperature. In the short life regime, fatigue strength was lower at 723 K than at 623 K, but in the long life regime it was nearly the same at both temperatures. At elevated temperatures, cracks were generated earlier at applied stresses below the fatigue limit at ambient temperature, indicating lowered crack initiation resistance. Small cracks grew faster at elevated temperatures than at ambient temperature, which became more noticeable with increasing temperature. After allowing for the elastic modulus, small cracks still grew faster at elevated temperatures.     

碳酸钙填充塑料成本分析

碳酸钙粉体经过活化、造粒处理填充到聚乙烯薄膜,可使填充制品成本降低。随着填料的增加,其加工性能逐渐变差,单位质量塑料产品体积减小。经测算,使用填充剂后成本的降低足以弥补因体积减小产生的损失。对于薄膜制品而言,填充量小于10%效益增加不明显;超过30%,则不容易稳定成膜,影响成品质量。     

On the performance of economic model predictive control with self-tuning terminal cost

In this paper, we analyze the closed-loop performance of a recently introduced economic model predictive control (MPC) scheme with self-tuning terminal cost. To this end, we propose to use a generalized terminal region constraint instead of a generalized terminal equality constraint within the repeatedly solved optimization problem, which allows us to obtain improved closed-loop asymptotic average performance bounds. In particular, these bounds can be obtained a priori. We discuss how the necessary parameters for the generalized terminal region setting can be calculated, and we illustrate our findings with two numerical examples.