Regulatory Light Chains in Cardiac Development and Disease

The role of regulatory light chains (RLCs) in cardiac muscle function has been elucidated progressively over the past decade. The RLCs are among the earliest expressed markers during cardiogenesis and persist through adulthood. Failing hearts have shown reduced RLC phosphorylation levels and that restoring baseline levels of RLC phosphorylation is necessary for generating optimal force of muscle contraction. The signalling mechanisms triggering changes in RLC phosphorylation levels during disease progression remain elusive. Uncovering this information may provide insights for better management of heart failure patients. Given the cardiac chamber-specific expression of RLC isoforms, ventricular RLCs have facilitated the identification of mature ventricular cardiomyocytes, opening up possibilities of regenerative medicine. This review consolidates the standing of RLCs in cardiac development and disease and highlights knowledge gaps and potential therapeutic advancements in targeting RLCs.     

重芳烃轻质化催化剂n（Ni）/n（Ni+Mo）的优化与分析

以β分子筛为载体,在保持金属总负载量不变的情况下,采用等体积浸渍法制备了4种不同n（Ni）/n（Ni+Mo）的催化剂。分别采用X射线衍射（XRD）、比表面积测试（BET）、氨程序升温脱附（NH₃-TPD）、氢程序升温还原（H₂-TPR）、氢程序升温脱附（H₂-TPD）和热重-差热分析（TG-DTG）等方法对催化剂进行了表征。结果表明,4种催化剂的酸量和酸强度相近,在n（Ni）/n（Ni+Mo）等于基准+0.2时,Mo与载体之间的相互作用最弱,其氢气吸附量最多且积炭量最少;采用某炼厂重整C₁₀⁺ 重芳烃对4种催化剂进行评价,结果表明n（Ni）/n（Ni+Mo）等于基准+0.2催化剂具有最优的催化活性和稳定性。上述结果表明,影响重芳烃轻质化催化剂活性和稳定性的关键因素是催化剂氢气吸附量的多少,氢气吸附量越多金属表面的溢流氢效应越明显,积炭前驱体被溢流氢及时消除,从而保护了催化剂的加氢活性中心不被积炭覆盖,有助于催化剂在较高活性下保持稳定。     

Fluorescent lamp promoted formaldehyde removal over CeO2 catalysts at ambient temperature

Exploring an alternative strategy with high efficiency and low cost to abate formaldehyde (HCHO) in indoor environment, is of increasing significance for people's health. CeO₂ catalysts prepared by hydrothermal, precipitation and calcination methods were investigated for HCHO removal at ambient temperature. It is found that indoor fluorescent light visibly boosts the catalytic performance of CeO₂ catalysts for HCHO decomposition at ambient temperature. Among the CeO₂ catalysts, CeO₂ prepared from hydrothermal method (CeO₂–H) exhibits a superior catalytic performance and an excellent durability by eight recycle times. Based on the characterization and analysis, the excellent catalytic performance of CeO₂–H is mainly contributed by its abundance of surface oxygen vacancies, and photogenerated electrons and hole activated by fluorescent light. This work shows a potential practicability in HCHO pollution elimination by taking full advantage of the existing lighting in indoor environments.     

高能束合金化技术的研究现状和发展趋势

综述了国内外以激光为代表的高能束表面合金化技术的研究现状，报道了当前表面合金化技术的研究问题，对高能束表面合金化技术的趋势进行了分析。指出激光合金化改性层的质量控制、合金化过程的自动化、合金化技术在工业生产中的推广应用是该技术的重要攻关方向。     

Preparation of fluoroacrylate nanocopolymer by miniemulsion polymerization used in textile finishing

Latex based on fluoroacrylate (TAN) and other comonomers was prepared via miniemulsion polymerization in the presence of stearyl trimethyl ammonium chloride (STAC) and 2, 2′‐azobis (2‐amidinopropane) dihydrochloride (ABAP) as a water soluble initiator. Light transmittance studies demonstrated that the light transmittance of prepared emulsions increases with the amount of TAN, STAC, cosolvent DPM, and hydrophobe DM. Given suitable reaction temperature and quantities of TAN, STAC, DPM, and DM, a copolymer emulsion of fluoroacylate with a particle size of 50 nm was produced. The water repellency tested on polyester fabrics displayed greater effectiveness than that of commercial products with higher fluorine content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1466–1472, 2004     

酸、碱溶液对脱脂蚕蛹的解剖结构影响

将脱脂蚕蛹分别置于清水、1%盐酸溶液和1%氢氧化钠溶液中,100℃浸泡处理20 min,采用电子光学显微分析技术观察脱脂蚕蛹的解剖结构。结果表明:①清水浸泡,蛋白质、甲壳素膨胀;②盐酸溶液浸泡,在蛋白质、甲壳素膨胀的同时,有蛋白的部分分解;③氢氧化钠溶液浸泡,蛋白质、甲壳素膨胀,蛋白质溶解,并伴有部分蛋白的分解。碱对蛋白层与甲壳层的层间有劈开作用。碱液能实现蛋白层与甲壳层的剥离。     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

可见光响应的"Cu核- Cu2O壳"型光催化剂性能的研究

以碱性染料结晶紫为目标污染物,金属卤化物灯为可见光光源,研究了自制的"Cu核-Cu20壳"微粒的光催化性能.实验结果表明,该催化剂对可见光有良好的响应,当固液比为1500,光照120min,质量浓度为60mg/L的结晶紫溶液色度和COD去除率分别达98%和92%.检测结果表明,光催化过程中有氢氧自由基产生,染料发生了彻底的降解.     

大面积水域浓度场测试方法及系统研究

针对大面积水域浓度场难以实现实时测量、测量精度不高等问题,采用了一种多通道荧光测试系统和方法。首先,基于单色光诱导荧光检测浓度(LIF)原理,使用探头获取离散点的浓度参数。然后,经总线或通信网络技术,将数百个测点连接起来。最后,通过数据总线或网络将采集的数据输送到中央测控计算机中,处理离散的数据后形成完整的浓度场。在恒定流浓度场中的试验结果表明,污染物测量相对误差均值不超过5%,单次测量相对误差最高值为8.33%,传感器线性度不超过5%,可检测的荧光素钠溶液浓度分辨率为0.001 ppm,系统测量稳定、精度较高。相较于其他浓度测量方法,该系统具有测量面积大、实时测量的优势,可为水污染防治等领域提供可靠的技术支撑。     

Efficient and color pure blue light emitting random copolymer with fluorene and fluorenylstilbene

A blue electroluminescent polymer, random copolymer of fluorenylstilbene and fluorene, was prepared by the nickel catalyzed coupling reaction. The structure and properties of the copolymer were analyzed by various spectroscopic methods. The obtained polymer had good solubility and thermal stability with high T_g. The polymer in thin film emits strong blue luminance (max=468 nm) with narrow bandwidth upon photoexcitation. PL spectrum of the polymer in the film is almost consistent with that of solution one as well as the EL spectrum, indicating that the aggregation and the excimer fluorescence are suppressed by the introduction of fluorenylstilbene comonomer. Moreover, the introduction of fluorenylstilbene comonomer lowered the oxidation potential to lead feasible hole injection, when the compared with poly(fluorene) homopolymer. The ITO/PEDOT/polymer/LiF/Al device showed the maximum brightness of 3500 cd/m² with a turn on voltage of 4.4, the maximum efficiency of 0.878 lm/W and blue emission with CIE chromaticity coordinates of ((x,y)=(0.17, 0.25)).