冬冷夏热地区户式空调设计与节能分析

以一单元式住宅的风道式户式空调系统为例，探讨了冬冷夏热地区户式空调的新风量确定方法，分析了户式空调的负荷特性，节能设计及户式空调系统的设计负荷与设计风量。     

宜昌站泄流能力变化对葛洲坝设计洪水影响

宜昌水文站是葛洲坝、三峡水利枢纽的设计依据站。葛洲坝水利枢纽动工修建和运行 ,对该站水位流量关系中低水部分产生了影响。探讨了该河段泄流能力的变化对葛洲坝水利枢纽设计洪水有无影响的问题。用1 967～ 1 999年实测资料对宜昌站以汛期平均水位为参数的水位流量关系曲线簇进行了检验 ,大部分年份最大日平均流量、3、7、1 5、30d洪量的偏差在± 4 %之间 ,说明曲线簇推流具有相当的精度。证明了宜昌河段中低水泄流能力的变化对葛洲坝水利枢纽设计流量和校核流量基本没有影响     

Acidity in upland and hill soils: Cation exchange capacity,pH and lime requirement

For 30 acid upland and hill soils, with initial pH from 3.5 to 5.8, and loss on ignition from 14% to 94%, cation exchange capacity varied with pH according to the relationship CEC = m pH+C, where m and C are characteristic of each soil. The slope m depended on loss on ignition (LOI), and is given by: m=Δ CEC/Δ=0.22 LOI+1.92. Because of these relationships, CEC measured at the natural pH of the soil (in 0.025 M MgSO₄ solution) is more relevant to field conditions than a conventional measurement at pH7. An improved method for estimating lime requirement (LR) of these soils was developed, based on the relationship found between LR and the difference in CEC (ΔCEC) between that at the natural pH of the soil and that at the target pH of 5.5: LR=1.12 ΔCEC+1.48. Lime requirement can therefore also be estimated from loss on ignition using the earlier relationships, and is given by: LR=(0.25 LOI+2.15) Δ+1.48, where Δ is the difference between the natural pH (in 0.025 M MgSO₄) and the target pH. Predictions based on this agreed well with results for a further 10 soils.     

船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

振冲法在砂场地地基处理中的应用

通过对典型振冲挤密法施工方法的研究，分析了该方法的加固机理，指出它可提高地基承载力、减少沉降和不均匀沉降，且能达到地基抗地震、抗液化能力的效果。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

钻孔灌注桩后压浆技术的应用与效果

介绍了后压浆技术提高灌注桩承载力的作用机理，并列举了四栋高层住宅楼工程中的应用情况，经试验结果分析，指出后压浆技术能大大提高灌注桩的承载力。     

数值方法确定地基承载力特征值的探讨

介绍了目前地基承载力的确定方法，研究了数值计算的可行性，并对其数值计算地基承载力的可靠性进行验证，指出应进一步完善确定地基承载力的方法，更好地解决群桩基础承载力的确定问题。     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。