接触传热表面粗糙度曲线的统计特征

测量了一般机械加工表面的轮廓曲线，基于小波变换提取了粗糙度曲线，分析了轮廓高度和接触峰高度的统计分布特征。研究结果表明，轮廓高度不服从严格的正态分布，但具有一定的正态性，而接触峰高度的统计特征与其评定标准有直接的关系。因此，对于接触热阻的计算模型来说，接触点数的计算应以合理选取接触峰的评定标准为前提。     

采用激光光刀的叶片三维面形测量方法

提出一种采用激光光刀的叶片三维面形测量方法。介绍了方法原理、系统结构、信息获取与处理方案,并给出了对实际飞机发动机叶片的面形测量结果。     

Velocity Profile in Fixed Beds: A Study on the Representativeness of the Experimental Measurement of Downstream Flow Characteristics

Although considerable progress has been made in the development of experimental techniques for investigating velocity distribution inside a fixed bed, these techniques were limited to special cases. Consequently, the velocity distribution is normally measured at downstream of the fixed bed and then this measurement is considered to be representative for the flow inside the bed. To evaluate the representativeness of this technique, this work presents a study of the change in the flow characteristics, starting from the boundary of the fixed bed within the pipe to a downstream position where the experimental measurement is taken, by using simulations based on computational fluid dynamics methods.     

大庆油田水平井分流压裂技术

水平井分流压裂的技术原理是将水平井的水平段分成若干个单元，在每个单元的最佳部位进行射孔，每段的射孔数由孔径、单元数、设计施工排量等参数决定，射孔方案为压裂方案的有机组成部分。大庆油田已有5口水平井实施分流压裂，根据油层厚度分为两类：裂缝限制在油层内和裂缝穿透隔层贯穿多个薄油层。通过肇57-平35井和肇57-平33井进行的分流压裂贯穿多个油层现场试验，介绍了大庆油田水平井分流压裂的设计方法、压裂液体系、现场施工控制方法和效果分析方法。微地震裂缝监测结果表明，在最大施工排量7．5m^3／mim条件下，一次施工形成3～4条裂缝，加砂量最大达到75m^3（陶粒），平均砂比达到35％以上。水平井采用分流压裂技术施工后，初期产能可达到相邻直井压裂后产能的2．0倍以上。如何检测裂缝是否穿透了隔层并贯穿多个油层，是指导水平井分流压裂技术的选井选层，提高压裂效果的关键技术。图8表2参2。     

杜84断块超稠油开发中后期稳产对策研究

对杜84断块超稠油生产中后期暴露的主要矛盾，即随着轮次升高，周期吞吐效果变差，井下技术状况日益变差。油层动用不均，汽窜加剧等问题进行了分析。并提出了相应的稳产对策-实施多井整体吞吐，大修复产，调剖等措施。现场应用证明，这些措施基本能够确保杜84断块超稠油中后期的稳产。     

Performance Evaluation of Packet Mobile Communications through Level Crossing Analysis

In this paper the performance of a packet mobile radio network is studied inthe presence of shadow fading outage intervals.Under quite general assumptions for the medium access protocol,the probability mass function of the sequence of packets that may be lostdue to an outage interval is derived. It is seen that long sequences of lostpackets are likely to occur for typical values of the mobile speed andshadowing correlation parameters.For delay constrained sources, e.g., voice, the analysis is mainly focused atderiving the probability function of the sequence of dropped packetsand the probability of dropping. For data sources, the delay statistic isalso derived. In the latter case, the effect of finite buffer length isaddressed. Simulation is used to verify the accuracy of approximations introduced in the analysis.     

多目标模糊优选理论在水资源系统中的应用

开放的水资源系统分析理论应是水资源学与系统科学等多种学科的结合 ,介绍一种新兴而实用的水资源系统分析技术———半结构性决策系统模糊优选理论的基本原理及其应用。     

The influence of the ion content of whey on the pH-activity profile of the β-galactosidase from Aspergillus oryzae

The pH-dependence of the reaction kinetics of lactase (β-galactosidase) from Aspergillus oryzae in different reaction media is presented in terms of a two-parameter model. The lactase from A. oryzae seems to have replaced the A. niger lactase on the market owing to a better activity/price ratio and may be utilised for lactose hydrolysis in acid as well as in neutral milk products. Its pH optimum is around pH 4.5. However, in the neutral pH-range its activity depended strongly on the salt content of the substrate solution. For example, its activity in whey (pH 6.5) fell to only 30% of its expected activity in a pure lactose solution at the same pH. The whey effect was the same for both soluble and immobilised lactase. The two parameter kinetic model, which included a term for competitive product inhibition gave excellent agreement with experimental data, and may thus be useful for the prediction of reactor performance with this enzyme.     

Development of a Sensor Fusion Strategy for Robotic Application Based on Geometric Optimization

Fusion of multi-sensor information is an important technology, which is growing exponentially due to its tremendous application potential in many areas. Effective fusion of data from sensors is very critical in increasing an intelligent system's capability to accomplish complex tasks. Appropriate fusion technologies are needed to be developed specially when a system requires redundant sensors to be used. More the redundancy in sensors, more is the computational complexity for controlling the system and more is its intelligence level. This research presents a strategy developed for multiple sensor fusion, based on geometric optimization. Each sensor's uncertainty has been modeled using classical Lagrangian optimization techniques. However, the uniqueness and effectiveness of the present technique lies on the fact that starting from the optimized value as initial estimate the accuracy of the sensory information has further been improved up to any pre defined bounded range, by developing two architectures – FFA (fission–fusion architecture) and FDD (fusion in differential domain). Sufficient evidences and analyses have been provided in the paper to show its effectiveness in various applications.