Study on ASTM E399 and ASTM E1921 standards

Costs of ASTM E399 and ASTM E1921 tests, which were developed to determine the fracture toughness (K_Ic) and the ductile–brittle transition temperature of ferritic steels, respectively, are considered high and the procedures are also very complicated. In this study, a method, which is more cost‐effective and easier to carry out, is proposed.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

The hydrogenation of triglycerides using supported alloy catalysts. I. Silica-supported Ni—Ag catalysts

Silica-supported Ni-Ag catalysts with a loading of 2·1·0.6% (w/w) total metal have been prepared using the precursors nickel dimethylglyoxime and silver nitrate by means of a simple impregnation method. The resulting catalysts were activated by calcination at 260°C in air, followed by hydrogen reduction at 450°C. They were then employed for soyabean oil hydrogenation at 1 bar H2 pressure and 160°C in a stirred batch reactor. Characterisation of the catalysts using temperature-programmed reduction and electron microscopy indicated that alloying of nickel and silver had occurred, but metal particle composition, for a given overall composition, varied with metal particle size and smaller metal particles were nickel rich. The hydrogenation activity and selectivity measurements revealed that the catalysts were more active and selective than a commercial nickel catalyst. Furthermore, the specific activities of the alloy catalysts were a maximum for alloys in the range 70–90 at. % Ni. However, the supported alloy catalysts also gave rise to greater trans isomerisation than the commercial catalyst. This is attributed to hydrogen deficiency caused by large triglyceride molecules blocking hydrogen chemisorption on small nickel particles (10–50 Å in diameter), leading to enhanced cis-trans isomerisation.     

江苏复杂断块高含水单元改善水驱效果的技术对策

在分析高含水开发单元特点的基础上,针对该阶段剩余油的品位、分布和油水关系极为复杂、挖潜难度大的技术难点,提出了适合江苏复杂断块油田高含水开发单元改善水驱开发效果的思路和工作程序、技术对策,并在真武油田高含水开发单元进行了实际应用,取得了良好的效果.     

Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

化学镀Ni—P镀层的X射线衍射研究

根据X射线衍射分析结果,对化学镀高P(含P>11wt％或19at％)Ni-P镀层加热时效时,镀层成分和加热温度对结构转变的影响作了研究,结果表明,高P共晶、过共晶(含P>11wt％或19at％)合金的结构转变有如下特征:(1)相同加热时效条件下,Ni-P合金的结构转变与成分有密切关系:(2)对同一成分的过共晶合金,Ni-P合金的结构转变与时效温度密切相关;(3)过共晶合金在290～360℃温度范围内时效处理,出现Ni_xP_y介稳相,X射线衍射分析认为Ni_xP_y为Ni_(12)P_5。