多量程数据采集记录装置的设计

通常的数据采集与记录装置不易实现多量程测量。通过对标度方程进行分析得知,要改变量程只须改变两个参数——标度因子和量程下限。我们设计了一个使用单片机的多量程数据采集和记录装置,能处理多达256种量程。本文叙述了算法分析、硬件和软件的设计以及该装置的性能指标。     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Solving regularized least squares with qualitatively controlled adaptive cross‐approximated matrices

The adaptive cross‐approximation (ACA) technique is applied to accelerating an inverse‐problem solver that estimates charge distribution on a dielectric spacer. The ACA generates an approximated system‐matrix that enables us to carry out high‐speed inverse calculation. We designed an approximation procedure based on ACA with some additional concepts, that is, (a) partitioning of matrix based on algebraic information, (b) approximation quality control based on matrix norms, and so on. The tested solver (LSQR for regularized least squares) with ACA demonstrates about 10 times faster performance than that without ACA. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(3): 10–18, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20326     

GPS在水面流速流向测量中的应用

传统的水面流速流向测量多采用经纬仪交会法,此法需要大量的人力和设备,工作量大且费时。近几年,随着全球定位系统(GPS)的广泛应用和实践,在一定范围内,采用GPS定位法替代经纬仪交会法施测水面流速流向。介绍了GPS定位法的测量原理、设备,以及测量方法。通过对GPS定位法的精度和优缺点的分析,得出采用GPS定位法施测水面流速流向具有较高的推广价值。     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

OPGW应用问题的探讨

根据多年的光纤复合架空地线(0PGW)应用经验与实践，从0PGW结构及组成、光纤余长、线路配合、金具配套、0PGW安装等方面，对0PGW应用中的若干问题进行详细的探讨。     

Quantitative measurement of gas hold-up distribution in a stirred chemical reactor using X-ray cone-beam computed tomography

Cone-beam type X-ray computed tomography (CBCT) is a potential method to measure three-dimensional phase distributions in vessels. An example for that is the measurement of gas profiles in stirred chemical reactors. Such data are highly valuable for the assessment and evaluation of chemical processes, for optimisation of the reactor and stirrer design, and for evaluation of computational fluid dynamics codes used to model the fluid flow and heat transfer in reactive systems. However, there are considerable difficulties for accurate quantitative measurements due to beam hardening and radiation scattering effects. In a theoretical and experimental work we have investigated the non-linear effects of both physical phenomena and developed a suitable measurement setup as well as calibration and software correction methods to achieve a highly accurate measurement of void fraction profiles with CBCT.     

Facial detection and location based on skin color and eye characteristic

This paper comes true a system of facial detection and location. Firstly, it realizes the facial detection of candidate region used skin color for the given image, and considers the influence of similar skin. Secondly, it realizes the location for eye region used the gray characteristic of eye and correction of central measurement, and makes further selection for facial candidate region. The end, it normalizes the facial image and makes it as front standard image, so realizes the facial characteristic location.     

火焰原子吸收光谱法测量污水中锑量的测量不确定度评定

通过火焰原子吸收光谱法对水中的锑量进行了测定,对影响测量结果的不确定度分量进行了量化的计算,从而得出影响锑量测量不确定的主要因素是测量样品消解液中的锑的质量浓度引起的不确定度.