提高16Mn连铸坯控轧合格率

１６Ｍｎ连涛坯进行控轧时，按铸坯碳当量的上限和下限，分别采用两种不同的控轧制度。在邯钢中板分厂试轧的结果，轧材合格率均达到９６％以上，投产后轧材合格率达到９８％以上。     

铸轧5052合金冷隔缺陷产生的机理研究

阐述了5052合金铸轧坯料生产时冷隔缺陷产生的机理,结合超型FATA—HUNTERΦ1003×1850mm机多年的生产实践经验,提出了消除铸轧冷隔缺陷的措施。     

A Study of Surface Deformation during Wire‐Rod Rolling of High Speed Steels using Experimental and Computational Techniques

The evolution of surface defects during shape rolling of high‐speed steel billets is studied using longitudinal surface defects prepared by machining and welding. The reduction of the defects during rolling in a production mill is compared to the total area reduction of the billets. Samples are collected after pass 4, 6, 8, 14, 19 and the final pass, 28, representing the finished 5.5mm wire. By inspecting the cross sections, the rotation of the billets from pass to pass is evaluated. Results from FE simulations on solid billets are compared to the experimental results. Generally, simulations predict less reduction than observed experimentally. In most cases cracks reduce most effectively followed by carbon steel welds and stainless steel welds.     

3t电渣钢9Cr2Mo工艺实践

为进一步提高冷轧辊电渣锭的内(外)质量、降低生产成本的要求,贵阳特钢采用400mm×300mm矩形连铸坯取代(φ)330mm铸锭做为电渣母材,在计算机全过程自动控制下,实现1支自耗电极重熔1支3吨电渣锭9Cr2Mo.电渣冶炼的填充比由初期的0.347提高到0.487,电渣锭成锭率由91.17%提高到96.87%,电渣重熔电耗由1762kWh/t下将到1477 kWh/t.     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

AlSn20Cu/Steel双金属板(带)复合轧制过程的厚度匹配

通过对AlSn20Cu/Steel双金属板(带)复合轧制过程变形区变形规律的分析，确定了轧制过程的总变形率与各分层变形率的关系，解决了实际生产中各分层原料的厚度匹配问题。     

切分轧制技术的发展与应用

简要回顾了近年来切分轧制技术的发展过程，着重介绍了几种典型的切分轧制工艺及其应用，并分析了该技术的发展动向。     

热宽带钢连轧机调宽轧制工艺参数研究

模拟宝钢２０５０ｍｍ热带钢连轧粗轧机组调宽轧制工艺，得到不同铸坯宽度压下效率、立辊轧制狗骨高度和宽度以及平轧轧制时宽展量等的变化规律。为制定合理的调宽轧制压下规程，Ｒ４机架轧后板坯实现最小切头、切尾损失，最大程度实现连铸坯宽度尺寸集约化提供了可靠的依据。     

连铸坯的液芯轧制

研究了连铸坯的液芯轧制，并结合日本川崎永岛厂的实例，证实了连铸坯液芯轧制的可行性，指出了钢锭和连铸坯液芯轧制的区别，及如何制造压应力状态，推导了坯壳应力与轧辊直径压下量，坯壳厚度的关系，并提出了用振摆式轧机实施连铸机液芯轧制的方案。     

轧制规程优化设计

介绍了板、带材压下规程及型材的孔型优化设计问题，并指出了设计特点与方法，给出了优化后的效果。为钢材及其它有色金属轧制规程的设计提供了设计方法。