有心力作用下限制质点运动范围条件的确定

分析应用有心力作用下质点运动的动力学特征求解轨道的方法,得出解决此类问题的过程中应用其动力学特征的优越性,提出限制质点运动范围的条件．     

SAMPAVE沥青混合料级配设计研究

SAMPAVE(Stress Absorbing Mixtures Pavement)沥青混合料是一种新型的延缓和防止反射裂缝的应力吸收层材料,具有抗裂、防渗、粘结等特性.根据变i法对SAMPAVE混合料进行矿料组成设计,并与AC-5、美国规范、科氏公司推荐的级配范围进行比较.结果表明,对于变i法设计的SAMPAVE混合料,级配上限、级配下限确定的沥青用量在设计工程级配沥青用量的±0.3%范围内,满足生产控制的要求,且SAMPAVE混合料具有优良的耐高温、耐低温、抗变形、耐疲劳、抗水损害等路用性能.     

微弱加性扰动对ADC影响的定量分析

在采集系统中,通常采用扰动技术来提高采样的SFDR和分辨率。本文通过傅立叶变换推导出加微弱加性扰动时ADC“总谐波失真”的数学表达式,从而定量分析微弱加性扰动对SFDR的影响;同时,利用卷积的图解法计算出微弱加性扰动时ADC的平均量化误差具体表达式,进而获取微弱加性扰动时ADC的分辨率。最后,采用matlab对加有微弱加性扰动的采样系统进行了仿真。结果表明,在ADC的输入信号上加微弱扰动信号,其分辨率有明显提高,SFDR提高了大约15dB。     

基于IEEE 80211e EDCA的下行信道动态无竞争接入机制*

为了改善无线局域网络服务质量,IEEE工作组形成了增补标准IEEE 802.11e,但是其增强的接入机制仍然不能完全满足IPTV、视频点播等类似场景的应用。为此提出了针对这一类应用场景的一种新的简单易行的下行信道动态无竞争接入机制,该机制基于MAC层队列长度信息动态调整下行信道接入参数,能有效地保护下行流媒体数据的传输,通过仿真结果验证了该机制有效并且实用。     

Research on indoor experimentation of range SAL imaging system

By means of advantages of both SAR and lidar, the combination of the techniques of (inverse) synthetic aperture and lidar makes it possible to obtain high resolution 2-D image. In this paper, an indoor experimental system of inverse synthetic aperture lidar imaging is given and a processing approach is presented. The given system is in the mode of lidar system with separated receiver and transmitter, which can effectively eliminate the jamming from the lens or/and the intersection between two optic fibers. ...     

Study on volume ratio and plasticizer screening of free coating membranes composed of ethyl cellulose and chitosan

The aim of this study was to optimize the formula of free blended coating membrane of ethyl cellulose (EC) and chitosan (CS), including their suitable ratio range and the best plasticizer used. The dry films were produced by a casting/solvent evaporation method, with different volume ratio of EC and CS solution plasticized by various plasticizers, respectively. The wet films were prepared by immersing dry films in pH 6.8 phosphate buffer saline (PBS) for 24 h. The promising ratio range of EC/CS was below 20/5 or 20/6 with various plasticizer, which was determined by comparing the viscosity of the blended solutions and the morphology of the blended films. The efficiency of plasticization was evaluated by measuring glass transition temperature (T_g). All the testing plasticizers have good compatibility with EC or CS and dibutyl phthalate (DBP) have the strongest efficiency inducing the lowest T_g (39.9°C) of the film. Mechanical properties were evaluated by the ratio of tensile strength (T) to elastic modulus (E). In the wet state, the films with DBP had the highest T/E value (1.2). The results of leaching of plasticizers also verified that DBP was the most stable plasticizer in the films. The release rates of tetramethylpyrazine phosphate (TMPP) through the pellets coated with the blended films of EC/CS (20 : 6 v/v) plasticized by various plasticizers showed that the more water‐soluble the plasticizer was, the more quickly TMPP dissolved from the coated pellets, which further indicated that the water‐insoluble plasticizers (such as DBP) could be more applicable to keep the sustained or controlled release property of the blended films in wet state. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1932–1939, 2006     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

CORRELATION OF DIFFUSION COEFFICIENTS FOR LIQUIDS AND DENSE FLUIDS WITH TEMPERATURE AND PRESSURE

On the basis of the free volume theory and activation energy concept,a fundamental equation whichtakes into account the effects of temperature and pressure has been developed.By introducing differentexpressions for the free volume and activation energy,several equations for fluid diffusion coefficients were derivedaccordingly.With the van der Waals free volume and intermal energy formula,a three-parameter model for fluiddiffusion coeffficients at moderate pressure was obtained.The grand average absolute deviation percent of 345data points (44 systems)for self-and infinite dilute inter-diffusivities is 2.32,against the results of the model ofCohen and Turnbull,4.13.In particular,by means of the modified Carnahan-Starling free volume equation,afour-parameter model with average abosolute deviation percent 2.64(30 systems,644 data points)for theestimation of dense fluid inter-and self-diffusivities at high pressures and in supercritical conditions was derived.The derived model is superior to the method of L     

Correlations between characteristics of maximum influence and degree distributions in software networks

Software systems can be represented as complex networks and their artificial nature can be investigated with approaches developed in network analysis.Influence maximization has been successfully applied on software networks to identify the important nodes that have the maximum influence on the other parts.However,research is open to study the effects of network fabric on the influence behavior of the highly influential nodes.In this paper,we construct class dependence graph(CDG)networks based on eight practical Java software systems,and apply the procedure of influence maximization to study empirically the correlations between the characteristics of maximum influence and the degree distributions in the software networks.We demonstrate that the artificial nature of CDG networks is reflected partly from the scale free behavior:the in-degree distribution follows power law,and the out-degree distribution is lognormal.For the influence behavior,the expected influence spread of the maximum influence set identified by the greedy method correlates significantly with the degree distributions.In addition,the identified influence set contains influential classes that are complex in both the number of methods and the lines of code(LOC).For the applications in software engineering,the results provide possibilities of new approaches in designing optimization procedures of software systems.     

Performance analysis for range expansion in heterogeneous networks

In this paper, the uplink and downlink performance of a two-tier heterogeneous network （HetNet） with range expansion （RE） is analyzed. Different from previous works, base stations （BSs） are modeled as a spatial Poisson point process. This model can not only capture the irregularity of the BS deployment but also lead to closed form expressions. With the analytical results, the impacts of several key parameters on the coverage and throughput performance are investigated. Our results justifies the effectiveness of RE and Pico deployment. Based on our analyses, certain attention should be made on the RE design to balance the uplink and downlink performance. Our analyses are corroborated by simulations and can thus serve as a flexible and quick guidance for system design without complicated and time-consuming system-level platform construction and simulation.