峡口水库沥青混凝土面板的施工与试验

以灌溉、防洪为主的峡口水库大坝，为沥青混凝土面板堆石坝，为研究低温抗裂性能，对沥青混凝土面板破损取样，进行了配比和多种力学性能试验，并与原面板设计指标进行了对比。由于面板经受住了－20℃以下的低温考验，其所用沥青指标、破损取样试验结果，特别是冻断低温指标，对确定水工沥青混凝土低温抗裂检验标准有重要参考价值。     

桩帽处理对灌注桩高应变检测的影响

本文给出砼灌注桩高应变检测中桩帽的施工工艺 ,并讨论其对测试结果的影响。     

硅光电负阻器件的构成原理与分类

将三端负阻器件与硅光电探测器相结合 ,通过新的构思成功地提出并构成了一类新型光电器件——硅光电负阻器件。文中报道了该器件构成的一般性原理 ,以及依据此构成原理确定的分类方法     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

巨型结构的抗震分析

采用ANSYS有限元程序对巨型框架结构、巨型框架隔震结构进行了抗震动力时程分析,讨论了两种结构在多条地震波作用下的动力位移及内力等地震响应,其计算结果对于确保巨型框架结构的抗震安全性具有较大的意义,对巨型框架结构的抗震设计有较大的参考价值。     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

Random errors caused by temperature in magnitude of principal strains evaluated ith 3-element strain gauge rosettes

The effects of the uncertainties associated ith the apparent strain and gauge factor data, given by the manufacturer, in the evaluation of principal strains are examined. Principal strains are obtained by a reduction of the strains measured ith electrical resistance strain gauge rectangular or delta rosettes. The theoretical analysis points out the relevance of the effects caused.     

碾压混凝土穿透型诱导缝不同扩展阶段的强度指标试验研究

在不同削弱度碾压混凝土轴拉试件的穿透型诱导缝周围粘贴了应变片，得到在不同应力状态下诱导缝应变发展规律为：在加载初期，离缝端不同距离的应变发展较为均匀，数值上相差不突出；随着荷载的增加，应变开始出现不均匀发展，离缝端越远，应变变化越缓慢；当接近最大荷载的阶段，缝端应变急速发展，试件瞬间断裂。应变从均匀发展变为不均匀发展，实质上隐含了诱导缝起裂、稳定发展、失稳断裂的整个过程，针对这一试验现象，结合断裂力学理论，建立了诱导缝不同开裂阶段的远场温度应力强度指标模型。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.