Dynamic analysis of the NPP pressure sensor system

The aim of the work was to develop on-line methods of control and diagnostics of pressure sensors at a NPP. The analysis was carried out along two lines:

1. i) The detection system including the sensor itself was modeled theoretically to obtain and study its transfer function, and to establish correspondence between the spectral characteristics of the pressure signal.

2. ii) The numerical processing of the signal using the AR technique to reconstruct the transfer function and evaluate the system's response, to a step impulse, as well as the spectral analysis. The hydraulic model presented indicate that the spectral lines observed at 10 Hz are due to longitu-dinal oscillations of water in the system branches, while the response time of the detection system is effectively the time of signal retardation in the porous ceramic diaphragms of the δ-cell of the sensor itself.

     

智能化红外焊缝检测仪的实时信号自相关分析

详细介绍了在改进红外焊缝检测仪的过程中实时信号的一种抗干扰方法－－自相关方法。重点离自相关方法的数学模型，软件框图及设计思想，并给出了实验结果。     

Stability analysis and antiwindup design of uncertain discrete-time switched linear systems subject to actuator saturation

This paper investigates the stability analysis and antiwindup design problem for a class of discrete-time switched linear systems with time-varying norm-bounded uncertainties and saturating actuators by using the switched Lyapunov function approach.Supposing that a set of linear dynamic output controllers have been designed to stabilize the switched system without considering its input saturation,we design antiwindup compensation gains in order to enlarge the domain of attraction of the closed-loop system in the presence of saturation.Then,in terms of a sector condition,the antiwindup compensation gains which aim to maximize the estimation of domain of attraction of the closed-loop system are presented by solving a convex optimization problem with linear matrix inequality(LMI)constraints.A numerical example is given to demonstrate the effectiveness of the proposed design method.     

提高Cr12MoV钢冷作模具寿命的措施

从原材料改锻、预备热处理、淬火及回火、深冷处理、表面强化处理等方面分析介绍了提高Cr12MoV钢冷作模具寿命的一些方法和措施 ,并通过实例表明 ,采用这些方法和措施可较大幅度地提高模具寿命     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

快干涂料铸渗法获得铸件表面复合层的研究

对快干涂料法铸渗工艺进行了研究。查明了影响铸件表面复合层质量的主要工艺因素,确定了最佳工艺参数,为生产实践提供了依据。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

The Structure of the Irreversibly Bound Adhesion Promoter-Substrate Interfacial Layer of γ-Aminopropylsilanetriol on Crystalline Si, as Measured by XPS and FTIR

The irreversibly bound interfacial layer deposited by the γ-aminopropysilanetriol adhesion promoter onto a crystalline silicon substrate, which remains even after profuse washing, was found by XPS to have resulted from the fragmentation and rearrangement of the original γ-aminopropylsilanetriol molecule. A mechanism is proposed, involving the homolytic scission of the terminal N-C bond. One of the subsequent reactions is believed to involve hydrogen loss by abstraction and the formation of a terminal vinyl group, which bonds to the substrate. Support for this mechanism is found in IR spectroscopy of this layer.