Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

回火过程应力场计算机模拟

回火过程应力场计算机模拟林家骝，杨振枢，于震宗，段贵明（清华大学）郭剑仁，史全兴，谢克仁（内蒙古第一机器厂）ＡＳｔｕｄｙｏｆＮｕｍｅｒｉｃａｌＳｉｍｕｌａｔｉｏｎｏｆＳｔｒｅｓｓＦｉｅｌｄｄｕｒｉｎｇＴｅｍｐｅｒｉｎｇ￥ＬｉｎＪｉａｌｉｕ；ＹａｎｇＺ...     

高层住宅结构设计

主要介绍长沙梦泽园高层住宅从基础到上部楼层各部位的结构设计,以及在设计、施工过程中所考虑的一些问题及处理方法。     

容器焊缝错边残余应力与载荷应力的测定研究

本文对焊接容器错边和不错边的焊接接头进行了电测法的残余应力测试，确定了焊接残余应力的大小及方向，并在加载的条件下，对各焊接接头测点进行了综合应力测试，并给出了受载条件下的应力分布。     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

Tensile Stress Relaxation of Alumina at High Temperature

The development of a tensile testing methodology for ceramics which enables a stress vs strain-rate response to be measured at high temperature is described. The test involves a carefully controled stress relaxation test at constant total strain using an experimental procedure and phenomenological analysis previously developed for metallic materials. It is demonstrated here with preliminary tests on alumina at 1050° and 1150°C. This offers, with further development, the possibility of establishing design stresses associated with low strain-rate behavior for structural applications. The results demonstrate that data covering four decades of strain rate may be generated in tests lasting a few hours. The inelastic strain consists of substantial anelastic recoverable strain in addition to a permanent creep strain.     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

一种无线传感器网络链式传输分簇路由协议

由于周围环境对无线传感器网络(WSNs)的影响,在布设到特殊环境下时会产生信号的衰减与损耗,导致通信不畅。针对此问题,提出一种以LEACH路由协议为基础适应特殊环境(长直空间)的新型路由算法。本算法采用链式传输,即从内部逐一将信号传输给距空间最外端且距基站位置较近的簇头,克服了内部节点死亡过快的问题。同时簇内采用链式传输并且改进簇头阈值与成簇半径,减小了能量消耗,提高了稳定性,克服了LEACH算法的不足。