非晶软磁合金的巨磁阻抗效应及应用

近来在ＦｅＣｏＳｉＢ等Ｃｏ基非晶体丝带中现了巨磁阻抗效应，由于在一小的直流纵向偏置场下该效应能使丝带两端的交流电压发生大而灵敏的变化，因而在磁记录头和传顺技术中具有巨大的应用科学潜能，受到各国学者的关注，本文简单介绍了巨磁阻抗效应的来源，并综述了近年来非晶体软磁合金材料的的巨磁阻抗效应及应用的研究进展，文章最后说明了尚待深入解决的问题。     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

Non-destructive evaluation of residual stresses in thin films via x-ray diffraction topography methods

Quantitative x-ray diffraction topography techniques have been used to measure the residual strain magnitude and uniformity of deposition for Mo and W sputtered films on Si(100) substrates. High sensitivity rocking curve measurements were able to determine differential strains for films as thin as 2.5 nm; while Bragg angle contour mapping had similar sensitivity and was also able to assess coating uniformity and stress distribution over areas covering a whole wafer. Measurements of strain versus film thickness over a range of 2.5 nm to 80 nm showed that a critical thickness exists for maximum residual strain. Growth beyond this range produces stress relaxation. This non-destructive type of analysis could be employed on a wide range of film-substrate combinations.     

Effects of shear flow on long-ranged correlations,spinodal demixing kinetics,and the location of the critical point and cloud point

A derivation of an expression for the shear rate-dependent Ornstein Zernike structure factor is discussed, together with the resulting anomalous behavior of the turbidity. The predicted scaling behavior of the turbidity, comprising the effect of both temperature and shear rate, is in good agreement with experiments on binary fluids. Then initial spinodal decomposition is discussed, and an explicit expression for the time- and shear rate-dependent effective diffusion coefficient is derived, which shows all the typical characteristics of anisotropic light scattering patterns that are observed experimentally for binary fluids. Next it is shown that the spinodal is shifted linearly with the (bare) Peclet number for not too large Peclet numbers, whereas the cloud point is singularly displaced into the unstable region due to a shear now. This is in agreement with an experiment on a two-polymer/solvent mixture and binary fluid mixtures. It is argued that light scattering is useless to determine the location of the spinodal of a sheared system.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

微机在应变测量中的应用

微机在应变测量中的应用，采用上位机和下位机组合方式．上位机为一台ＩＢＭ－ＰＣ／ＸＴ微机，用于对数据进行后处理．下位机以Ｚ８０－ＣＰＵ为控制器，由传感器、转换器、接口及外设等组成数据采集器，实施对应变、压力和位移等参数的采集、显示和打印（即数据的预处理）．上位机和下位机之间的数据传输，采用串行的方式，通过ＲＳ－２３２接口完成．本文主要以应变的采集处理为例，介绍系统功能、硬件配置及软件设计．     

陶瓷传感器的微型化与集成化

本文主要介绍陶瓷传感器在微型化及集成化方面的进展；指出了集成化多功能传感器存在的技术问题及未来发展趋势。     

内燃机车曲轴中频淬火过程的数值模拟

借助 ANSYS大型有限元分析软件 ,实现了 16 V2 4 0曲轴淬火过程的计算机模拟 ,模拟结果可直观地显示出任一时刻曲轴表面及内部的温度分布、冷却曲线以及淬火结束后的残余应力分布 ,并能预测淬硬层深度。同时对比了轴颈内圆角处进行淬火和不进行淬火两种工艺的效果 ,为现场提供了用虚拟现实方法详尽分析和研究淬火工艺的工具。     

全20CrMnTi表面激光重熔的组织与性能研究

本文对激光重熔20CrMnTi材料表明改性层显微组织分布特征、表面硬度分布规律以及残余应力状态作了研究,结果表明,表面改性层由熔融层、相变硬化层及过渡层组成,且材料表面显微硬度得到大幅度提高,表面硬度达到HV841,约提高4倍。硬化层深度约1mm。残余应力测试得出最大残余应力出现在熔凝带中心,表现为压应力。随着离中心距离的增大,残余应力逐步降低,到熔化带边缘,表现为低幅值压应力;而熔池的外边缘应力在热影响区则转变为拉应力状态。