国产清梳联短绒的控制

阐述了短绒产生的原因与危害,分析了清梳联短绒增加较多的原因,提出了清梳联工序有效控制短绒的措施,认为应采取“连续喂棉、薄喂轻打”措施,减少纤维损伤;同时注意开松梳理适度,排除结杂和减少短绒兼顾。     

采用MATLAB图像处理技术在鱼病诊断中的应用

本文介绍了一种可以对水产养殖中鱼的病变情况进行监控的系统。通过MATLAB软件中强大的图像处理功能,对读入的图像进行中值滤波、灰度处理和二值处理,然后根据收缩与扩张的原理,编写程序,对二值图像进行数次收缩与扩张,以去除杂质点,最后采用区域矩特征的概念,统计出白色像素的数目,与统计数据相比较,即可判断出是否出现鱼类病变死亡等异常情况。     

交通信号智能控制仿真系统

根据交通信号智能控制过程中的各种复杂情况,研制了一个微观仿真的实用系统。微观仿真系统可实现交通路网编辑模块、交通参与者模型、交通信号控制模型、方案评价模型等,还能够实现多种方案的动态实时仿真,提高信号控制方案选择的有效性。     

对我国油脂深加工的化工产品综述

对我国加速开发植物油脂深加工产品及经济重要性、产品用途、生产工艺等方面作了探讨。介绍了较为成熟的生产工艺,提出了开发生产环氧大豆油、脂肪酸、硬脂酸、甘油、亚油酸、磷脂、糠蜡、植酸钙、肌醇等多种油脂化工产品,创造经济效益的建议。     

High-speed ground moving target detection research using triangular modulation FMCW

The frequency modulated continuous wave (FMCW) radar has the characteristics of low probability of interception, good hidden property and the ability to counter anti-radiation missiles. This paper proposes a new method for high-speed ground moving target detection (GMTD) using triangular modulation FMCW. According to the characteristic of the opposite range shift induced by the upslope and downslope modulation FMCW, the upslope and downslope are imaged, respectively. After compensation of continuous motion of the platform and time difference between upslope and downslope signals for imaging, the moving target can be detected through displaced phase center antenna (DPCA) technology. When the moving target is detected, the moving target image is extracted, and correlation processing is used to obtain the range shift, which can be used to estimate the target radial velocity, and further to find the real position of the target. The effectiveness of this method is verified by the result of computer simulation. __________ Translated from Journal of Xidian University, 2008, 35(4): 586–591 [译自: 西安电子科技大学学报(自然科学版)]     

Stereo effect of image converted from planar

Research on planar-to-stereo image conversion has significant theoretical and practical implications for image processing. In this paper we use a method which segments an image into sub-blocks to perform this kind of conversion; parameters such as random variables are used for conversion control. We use two quantitative criteria, cross-entropy and root-mean-square error, to evaluate the stereo effect. Furthermore, the stereo effect that the random variables create is discussed. The results of the experiment show that, (i) when all random variables have the same distribution, different values of these random variables only slightly affect the stereo effect; and (ii) when different distributions are applied to the random variables, the cross-entropies or root-mean-square errors are slightly different, which indicates different distributions have a small influence on the stereo effect. Generally, we recommend normal distribution for better stereo effect in most cases.     

Optimization of abrasive water jet cutting of ductile materials

Full factorial design of experiments was developed in order to investigate the effects of jet pressure, abrasive mixing rate, cutting feed, and plate thickness upon three response variables, surface finish of cutting wear zone, percentage proportion of striation free area, and maximum width of cut. The set of sixteen experiments was performed on each of the following two ductile materials: AISI 4340 (high strength low alloy steel, hardened to 49HRc) and Aluminum 2219. Analysis of Variance (ANOVA) was performed on experimental data in order to determine the significance of effects of different parameters on the performance measures. It was found that cutting feed and thickness were highly influential parameters, while abrasive mixing rate is influential upon surface roughness only. Strong interaction was found between jet pressure and workpiece material. Multi-criteria numerical optimization was performed in order to simultaneously maximize/minimize different combinations of performance measures.     

跟踪-微分器在全捷联制导中的应用分析

以仅能获取角度信息的全捷联导引头为研究对象,针对采用直接微分提取惯性视线角速率时存在的噪声放大问题,基于跟踪微分器设计了一种全捷联制导信息提取算法。结合导引头的性能指标要求,对3种不同形式跟踪微分器的提取效果进行了对比分析。仿真结果表明,采用非线性微分器进行惯性视线角速率提取,可以减小延迟时间,避免噪声放大,有效提高制导精度,具有一定的工程应用价值。     

光谱分析的微机测试

介绍了一种用光电倍增管将光信号转换为电信号,再将此信号放大经模数转换后输入到微机、打印机等设备的一套光谱分析的微机处理方法,此种方法与传统的干板照像法进行比较,在进行光谱分析时省时、省力、误差小,实现了光谱分析的微机化。