电石渣在环氧丙烷生产中的循环利用

总结了电石渣生产环氧丙烷工艺中的设计与应用。运行情况表明，该工艺具有明显的经济效益和社会效益。     

Sintering of Ceramic Particulate Composites: Effect of Matrix Density

Composites consisting of a fine-grained, polycrystalline zinc oxide matrix and <10 vol% coarse, rigid silicon carbide inclusions were prepared by the same mixing procedure and then compacted to produce samples with matrix densities of 0.45 and 0.68 of the theoretical. The samples were sintered under identical temperature profiles in separate experiments that employed either a constant rate of heating of 4°C/min or near isothermal heating at 735°C. The ratio of the densification rate of the composite matrix to the densification rate of the unreinforced zinc oxide was found to be independent of the initial matrix density. This ratio increased significantly with temperature in the constant-heating-rate experiments but was relatively constant in the isothermal experiments. The results indicate that microstructural coarsening may be an important mechanism for explaining the reduced sinterability of polycrystalline matrix composites.     

Influence of composition and molecular mass on the morphology,crystallization and melting behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends

Results are reported on the influence of composition and molecular mass of components on the isothermal growth rate of spherulites, on the overall kinetic rate constant, on the primary nucleation and on the thermal behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends. The growth rate of PEO spherulites as well as the observed equilibrium melting temperatures decrease, for a given T_c or ΔT, with the increase of PMMA content.Such observations are interpreted by assuming that the polymers are compatible in the undercooled melt, at least in the range of crystallization temperatures investigated. Thermodynamic quantities such as the surface free energy of folding σ_e and the Flory-Huggins parameter χ₁₂ have been obtained by studying the dependence of the radial growth rate G and of the overall kinetic rate constant K from temperature and composition and the dependence of the equilibrium melting temperature depression ΔT_m upon composition, respectively.     

Influences of zinc oxide and an organic additive on the electrochemical behavior of pure aluminum in an alkaline solution

The corrosion behavior of pure aluminum in inhibited and uninhibited 4 MKOH was investigated by means of hydrogen collection, polarization curve measurement and electrochemical impedance spectroscopy (EIS). The results showed that the corrosion of pure aluminum was greatly inhibited by the addition of ZnO and dimethyl amine epoxy propane (designated as DE). EIS and EDAX analyses revealed that ZnO produces its effect by depositing on the aluminum surface, which increases the overpotential of hydrogen evolution. It was also found that the addition of DE could greatly improve the deposition of zinc layers.     

侧链为亚乙氧基结构的EVOH梳型聚合物的合成

以乙烯-乙烯醇共聚物(EVOH)为原料，制备了一种主链为疏水的聚乙烯链段，侧链具有亚乙氧基结构的多羟基梳形聚合物，用元素分析法、凝胶渗透色谱法、核磁共振谱法对其进行了结构表征；用热重分析法和示差扫描量热法对其热学性能进行了表征。结果表明，接枝后产物的玻璃化转变温度在-52--40℃之间，熔点在55～600℃之间，由于侧链的引入破坏了EVOH的结晶，因此梳形聚合物的热分解温度比EVOH降低了约20℃。     

Hardness and Fracture Toughness of SiC-Particle-Reinforced MoSi2 Composites

The indentation technique has been used to evaluate the hardness and fracture toughness of SiC-reinforced MoSi₂ composites made by hot-pressing. It is seen that the toughness increases with increasing indentation crack length (under increasing load) and a probable mechanism responsible for this behavior is described. It is also observed that there is an optimum volume fraction of SiC particles for which the maximum fracture toughness of the composite can be achieved.     

长链脂肪族氧化胺对合成纤维的抗静电作用

研究了题示表面活性剂对涤纶和丙纶的抗静电性能,探讨了不同结构的脂肪族氧化胺的抗静电效果和环境湿度、上油量对其抗静电性的影响。认为:氧化胺在低湿(30%RH)条件下也能保持良好的抗静电作用;二甲基十二烷基氧化胺在同类物中的抗静电性最佳(比电阻为0.95×10~8Ω);氧化胺作丙纶油剂的抗静电组分,可提高丙纶的加工性能和成品质量;氧化胺在纤维上的上油量(0.06%)相当低时也显示了较好的抗静电作用。     

Effect of the metal oxide loading on the activity of silica supported MoO3 and V2O5 catalysts in the selective partial oxidation of methane

Precipitated silica catalysts loaded with either MoO₃ (0.2–4.0 wt%) or V₂O₅ (0.2–5.3 wt%) have been studied in the selective partial oxidation of methane to formaldehyde with molecular oxygen at 520 °C. The functionality of the SiO₂ surface towards the formation of HCHO is significantly promoted by V₂O₅, while it is depressed by the MoO₃.