Critical-point drying versus freeze drying for scanning electron microscopy: a quantitative and qualitative study on isolated hepatocytes

Critical-point drying and freeze drying were compared both quantitatively and qualitatively as preparative procedures for scanning electron microscopy. Isolated hepatocytes were used as model cells. Nomarski differential interference contrast microscopy was used for light microscopic measurements of the hepatocytes in the unfixed, the glutaraldehyde fixed, the glutaraldehyde + OsO₄ fixed, the critical-point dried and the freeze dried states. Critical-point dried hepatocytes were found to shrink to 38% of glutaraldehyde + OsO₄ fixed volume, whereas optimal freeze dried hepatocytes (frozen in water saturated with chloroform and freeze dried at 183 K for 84 h) were found to shrink to 51% of glutaraldehyde + OsO₄ fixed volume. Transmission and scanning electron micrographs of the critical-point dried cells showed well-preserved ultrastructure and surface structure. Micrographs of the freeze dried cells showed ultrastructure destroyed by internal ice crystals and surface structure destroyed by external ice crystals. Double-fixed isolated hepatocytes were shown to swell during storage in buffer and to shrink during storage after critical-point drying. For low magnification scanning electron microscopy (up to about 3000 times) both critical-point drying and freeze drying can be used. However, for high magnification scanning electron microscopy, critical-point drying is superior to freeze drying.     

用化学腐蚀制备多孔硅太阳电池减反射膜的研究

采用HF HNO3溶液化学腐蚀 ,在硅片上制备减反射效果优良的多孔硅太阳电池减反射膜 ,借助原子力显微镜 (AFM)和X光电子谱 (XPS)对其表面形貌和成分进行观察 ,发现该膜与电化学阳极腐蚀得到的多孔硅具有相似性 ,其主要成分为非化学配比的硅的氧化物SiOx(X <2 )。采用带积分球的光度分光计 ,测得形成多孔硅减反射膜后 ,硅片表面反射率大大下降 ,,在波长 330～ 80 0nm范围反射率只有 1 5～ 2 9%。研究指出这种强减反射作用 ,与多孔硅具有合适的折射率及其多孔特性的光陷阱作用有关     

Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

Influence of the intrinsic layer characteristics on a-Si:H p–i–n solar cell performance analysed by means of a computer simulation

In this paper a set of one-dimensional simulations of a-Si:H p–i–n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift–diffusion and the generation–recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy.     

Critical Speed Control of a Solar Car

The World Solar Challenge is a 3000 km race for solar powered cars across the Australian continent from Darwin to Adelaide. Each car is powered by a panel of photovoltaic cells which convert sunlight into electrical power. The power can be used directly to drive the car or stored in a battery for later use. Previous papers (P. Howlett, P. Pudney, T. Tarnopolskaya, and D. Gates, IMA Journal of Mathematics Applied in Business and Industry vol. 8, pp. 59–81, 1997; P.G. Howlett and P.J. Pudney, Dynamics of Continuous, Discrete and Impulsive Systems vol. 4, pp. 553–567, 1998) using a simplified model of the battery, have shown that the optimal strategy is essentially a speedholding strategy. In this paper, with a more realistic model of the battery, we show that the optimal driving strategy is a critical speed strategy. For an optimal journey with no beginning and no ending the solar car must always travel at the critical speed. For an optimal journey of finite length the speed must be close to the critical speed for most of the journey. The critical speed depends on the solar power and will normally vary slowly with time.     

啤酒废酵母干燥工艺设计的研究

该文设计了一套适用于年产量5万吨以上啤酒厂废酵母干燥的生产工艺，提出了设计要点，并对干燥工艺进行了适用性分析。     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

生物除臭滤池在污水厂污泥处理段的除臭效能

对采用天然有机滤料和合成无机滤料的生物除臭滤池在加拿大多伦多市Ash-bridge’s Bay污水厂污泥处理站的干化和转运段的应用效果进行了分析。详细介绍了污泥脱水工艺、臭气的产生及其组分，进而对软木树皮滤料和矿物合成永久性滤料的除臭效果进行了比较。还讨论了一些具体的运行经验，并采用动态模型对不同条件下的运行数据进行了分析。