合成直链烷基苯环境友好固体酸催化剂的研究 Ⅲ .催化剂失活原因分析

采用固定床反应器,对催化剂的稳定性进行了初步评价。在120℃、空速相同、液固反应条件下,高苯烯比时催化剂的稳定性明显高于低苯烯比时;在苯烯比和空速相同、液固反应条件下,相对低温反应时,催化剂的稳定性明显高于高温反应。IR分析结果表明,同新鲜和反应后未失活的催化剂相比,失活后催化剂的活性组分特征衍射峰消失,出现的新的特征衍射峰可能同—CH基的振动有关。TG分析结果表明,失活后催化剂在空气流中焙烧,失重幅度比新鲜催化剂大。     

固体中光声拉曼效应的理论分析

从非线性波动方程出发，运用准平衡模型以及热弹理论，对固体样品中光声拉曼效应进行理论分析，导出了脉冲激光泵浦下光声拉曼信号的解析表达式，并总结分析了固体中光声拉曼效应的一些原理特性、实验问题和应用价值。     

Sorption of Acid Green 25 on chitosan: Influence of experimental parameters on uptake kinetics and sorption isotherms

Acid Green 25, which is a diazoic dye bearing two sulfonic groups, is efficiently sorbed on chitosan. The protonation of chitosan may explain the electrostatic attraction of this anionic dye and that its optimum pH is close to 3. Preliminary protonation of amine groups (obtained by contact with a sulfuric acid solution) reduced the variation of solution pH following sorbent addition but significantly reduced sorption performance: the maximum sorption capacity of raw chitosan, 525 mg dye/g (0.84 mmol dye/g), was halved by acidic preconditioning. The acidic conditioning also reduced the kinetic rate—the time necessary to reach equilibrium increased up to threefold depending on the experimental conditions. The size of sorbent particles influenced sorption kinetics and equilibrium because of resistance to intraparticle diffusion, but the sorption appeared to occur not only at the surface of the sorbent but also in the intraparticle network of the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1073–1080, 2003     

纯镁对碳化硼颗粒的常压浸渗

本文研究了纯镁对不同致密度的碳化硼(B₄C)颗粒基片的常压浸渗性;讨论了镁液对B₄C颗粒聚集体常压浸渗的影响因素;提出了浸渗模型。研究表明,纯镁在氩气保护下,800～850℃温度范围保温30min即可浸渗B₄C颗粒聚集体。浸渗深度和宽度随加热温度升高和保温时间延长而增加;常压浸渗的B₄C_P/Mg复合材料具有很高的硬度,B₄C颗粒在基体中分布较均匀。     

腐蚀算法在重建一类特殊管道中的应用

针对一类特殊而不能直接对其观察的管道（如动物的血管），为了准确了解其内部特征和形态，借助计算机给出了一种用腐蚀算法来重建管道原形的方法。这种方法简单易行，而且精确度高。     

Municipal solid waste conversion to energy

In recent years it has been recognised by an increasing number of nations that there is considerable energy potential within MSW. As a result many countries have established R,D& D programmes to examine methods of exploiting this potential. The IEA's MSW Conversion Activity was set up in 1986 to provide an infrastructure for sharing information and co-ordinating work in this area internationally. This Activity was extended in 1989 and currently a total of 9 nations participate in it.

To cope with the wide scope of the area (encompassing both biological and thermal processing of MSW) the Activity was divided into three subgroups or Expert Working Groups (EWGs). Each of these dealt with a distinct area of expertise:

1. •Downstream effects of source separation and screening of MSW

2. •Sampling and analytical protocols

3. •Landfill gas

In addition to these groups a central secretariat based at Harwell (UK) has provided guidance, established and administered databases of contacts and produced a series of national reports.

This paper describes the achievements of the Activity and discusses work proposed for the future.     

Properties and Performance of Cation-Doped Ceria Electrolyte Materials in Solid Oxide Fuel Cell Applications

Cation-doped CeO₂ electrolyte has been evaluated in single-cell and short-stack tests in solid oxide fuel cell environments and applications. These results, along with conductivity measurements, indicate that an ionic transference number of ∼0.75 can be expected at 800°C. Single cells have shown a power density >350 mW/cm². Multicell stacks have demonstrated a peak performance of >100 mW/cm² at 700°C using metallic separators.     

钼精矿结球机理及对策研究

钼精矿产品质量的提高、粒度变细,干燥过程中结球现象严重。在氧化钼的焙烧过程中MoS2残留量较高。本文针对这一现象,分析了其结球机理,提出了相应对策及解决办法。     

Bi3+对纳米MnO2水热合成的影响研究

在中性和酸性条件下，以MnO2作为锰源，通过水热合成了纳米MnO2，通过XRD和TEM对产物进行的观察表明，在酸性条件下，向溶液中添加一定量的Bi^3 ，产物的晶型由α型向γ型转化，产物形貌由针状、丝状向颗粒状转变。     

Compressive deformation of semi-solid SiC_p/ZA27 composites

1　INTRODUCTIONTheapplicationofcastingSiCp/ZA2 7compositesisgreatlylimitedduetotheinhomogeneousdistribu tionofSiCpandtheporosityexistedinthematrix[1] .However,semi solidformingtechnology (SSF )e mergedintherecentyearscannotonlydecreaseore liminatetheporosityandenhancethecompactnessofthematrix ,butalsoimprovetheuniformdistributionofthereinforcementthroughtheredistributionofthereinforcementfromitsuniquecharacteristicsofmouldfilling[2 ] .Inaddition ,SSFisanearnet shapeform ingtechnology …