LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

核电材料在模拟反应堆环境中应力腐蚀破裂测试技术与性能评价

简要介绍了采用慢应变速率试验，Ｕ型弯曲和Ｃ形环试验等技术，分别对８００合金，３０４和３１６及３１６Ｔｉ不锈钢Ａ５３３Ｂ压力容器用多在模拟核反应堆环境中的应力腐蚀破裂敏感性性进行的试验研究的一些主要结果；并结合电化学测试和表面膜俄歇电子能谱分析结果进行了讨论。     

用快切装置替代备自投装置提高厂用电安全可靠性

指出目前厂用电切换装置存在的不足，分析了快切装置的基本原理以及厂用电事故下的成功快切对电厂安全生产的意义，说明了在厂用电切换中尽快应用快切装置的必要性。     

心电图信号的频域分析

提出了一种简便有效的、由心电图（ECG）曲线提取QRS-T复合波的新方法，从而获得P波（当房颤未发生时）或f波（当房颤时）；利用功率谱、自相关、互相关等信号处理技术，对它进行了处理和分析，特别是，比较了未房颤时和发生房颤时的相关信息的显著差别。     

探讨电石法PVC烟气治理方法

分析了电石法PVC生产链中电石炉烟气及电厂烟气二氧化硫的排放情况,指出利用电石炉烟气中的CO合成氨、再将合成氨用于燃煤电厂烟气的"氨法"脱硫是具有较大应用潜力的循环经济产业链。     

环境敏感因素对电站正常蓄水位选择的影响

卜寺沟水电站预可阶段正常蓄水位是考虑规划成果、地形、地质务件、梯级衔接、水库淹没、筑坝技术、水能资源利用等因素综合初选的.从理论角度分析,水库淹没时水库内寺庙的影响,按全部淹没进行经济补偿处理代价较小;其社会环境敏感因素对正常蓄水位的选择不应起决定性作用.但是,考虑到少数民族群众、僧侣和地方政府的要求,适当降低正常蓄水位,以减少对扎西日岗寺庙的影响,将带来较积极的社会影响.     

Evaluating the mixing performance of a ribbon blender

This paper investigates the effects of processing and equipment parameters of a ribbon blender (i.e. loading method of lubricant, fill level, blade speed and blade design) on magnesium stearate homogeneity. A core sampling technique is used to obtain at least one hundred samples per sampling event, which are extracted throughout the blender and yield a thorough characterization of the entire bed. The results presented here can be used as a guideline to develop appropriate blending processes and characterization protocols for ribbon blenders.     

NOPD技术在板结构声辐射控制中的实验研究

本文应用NOPD技术设计了一种复合多层板，按照四边固定薄板结构的模态振型，对不同的NOPD填充形式，进行声学实验，来评价不同填充形式在降低板类结构声辐射方面的效果，分析了该类板结构声振耦合的关系并验证了NOPD技术对声辐射控制的作用。