玻璃钢包扎在煤气管道加强上的应用

介绍了玻璃钢包扎煤气管道的施工材料、施工流程及要点，指出了此方法应用在煤气管道加强上的优点。     

Studies on the corrosion behavior of cerium-implanted zircaloy-4 with GAXRD

In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zircaloy-4, specimens were implanted by cerium ions with a fluence range from 1×10¹⁶ to 1×10¹⁷ ions/cm² at maximum 150°C, using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the cerium ion implantation in the oxide films. Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zircaloy-4 in a 1 N H₂SO₄ solution. It was found that a significant improvement in the aqueous corrosion behavior of zircaloy-4 implanted with cerium ions compared with that of the as-received zircaloy-4. The improvement effect will declined with raising the implantation fluence. The bigger is the fluence, the less is the improvement. Finally, the mechanism of the corrosion behavior of the cerium-implanted zircaloy-4 is discussed.     

Simulation of cup-cone fracture using the cohesive model

The cohesive model is used for the prediction of the crack path during stable crack extension in ductile materials. The problem of crack-path deviation is investigated by means of simulation of crack propagation in a round tensile bar. The respective phenomenon is known as cup-cone fracture. It is shown that the model is able to predict the failure mechanism, which consists of normal fracture in the center and combined normal/shear fracture in the so-called “shear lips” at the specimen’s rim. The damage evolution and crack path predicted by the model are presented. The effect of the normal and shear failure parameters on the crack-deflection point and several aspects of the finite element mesh are discussed.     

Reducing Average and Peak Test Power Through Scan Chain Modification

Parallel test application helps reduce the otherwise considerable test times in SOCs; yet its applicability is limited by average and peak power considerations. The typical test vector loading techniques result in frequent transitions in the scan chain, which in turn reflect into significant levels of circuit switching unnecessarily. Judicious utilization of logic in the scan chain can help reduce transitions while loading the test vector needed. The transitions embedded in both test stimuli and the responses are handled through scan chain modifications consisting of logic gate insertion between scan cells as well as inversion of capture paths. No performance degradation ensues as these modifications have no impact on functional execution. To reduce average and peak power, we herein propose computationally efficient schemes that identify the location and the type of logic to be inserted. The experimental results confirm the significant reductions in test power possible under the proposed scheme.     

盘山闸扩建工程水工模型试验研究

辽河干流堤防安全泄量为5000m3/s,盘锦城市防洪工程竣工后,其安全泄量为6800m3/s。而盘山闸的设计泄流能力仅为3000m3/s。通过本模型试验研究进一步确定扩建工程方案的合理性。     

导流能力测试系统的研制

压裂后裂缝的导流能力直接关系着压裂缝的渗流能力，是客观评价压裂效果的重要指标之一。文章介绍了基于AT89C52单片机的导流能力测试系统的系统要求、测试原理以及其设计方案，阐述了各个测控通道，给出了测控系统电路方框图。     

湿H2S环境中金属材料腐蚀的研究

介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法.最后,指出了应加强H2S腐蚀的基础性和系统性研究的研究方向.     

关于混凝土钻芯取样法有关标准的讨论

本文对国内不同行业有关混凝土钻总取样方法的标准进行了讨论，供月行在使用和修订相应标准时参考。     

部件试验模态综合的简便方法

本文将一种基于完备模态基的模态综合技术应用于子结构的试验模态综合,获得成功。这种半试验半理论的模态综合方法是一种较为简便的、要求试验工作量较小的试验模态综合法,因为它只要求测量子结构的振动模态和频率即可。数值仿真结果表明,这种简便的试验模态综合法是行之有效的。     

异步电机性能微机测试系统设计

结合工程实际介绍了异步电机计算机辅助测试（CAT）系统的硬件、软件组成、技术方案确定以及设计原则。现场运行表明，该系统稳定可靠，且具有较高的性能价格比。