磷酸盐激光玻璃非激活吸收系数测量研究

介绍了高功率激光放大器系统中磷酸盐激光玻璃的静态透过率测量。在正常运行条件下,4片长按布儒斯特角放置的国产N31钕玻璃片对1.054um的激光波长平均静态透过率为94.5%,介质的损耗系数为0.294%cm-1,平均非激活吸收系数为0.146%cm-1。在此基础上对片状放大器的增益系数的测量结果进行了修正,获得了5.25%cm-1的小信号增益系数。     

Nd3+ Doped Silicate Glass Photonic Crystal Fiber with Random Hole Distributions

The fabrication of one kind of large core area Nd3 doped silicate glass photonic crystal fiber, and demonstration of the fiber's waveguidence properties were reported. This fiber owns a random air hole distribution in the cladding. The measured minimum loss of this kind of fiber is 10 dB·m-1 at 660 nm. These fibers can sustain only a single mode at least over wavelength ranging from 660 nm to 980 nm.     

Delay-insensitive codes — an overview

The problem of delay-insensitive data communication is described. The notion of delay-insensitive code is defined, giving precise conditions under which delay-insensitive data communication is feasible. Examples of these codes are presented and analyzed. It appears that delay-insensitive codes are equivalent with antichains in partially ordered sets and with all unidirectional error-detecting codes. Tom Verhoeff received the B.S. and M.S. degrees in mathematics from Eindhoven University of Technology, The Netherlands, in 1985. He is currently an Assistant Professor at the Department of Mathematics and Computing Science of the same university. His main research interests are parallel computations, especially formalisms for their specification and design, and their implementation as delay-insensitive VLSI circuits.     

Improvement on threshold proxy signcryption scheme

Signcryption is a public key or asymmetric cryptographic method that provides simultaneously both message confidentiality and integrity at a lower computational and communication cost. This paper presents a （t, n） threshold proxy signcryption scheme in which no less than t proxy agents in the proxy group can produce the signcryption cryptogram. combines the functionality of threshold proxy signing and encryption. The proposed scheme combines the functionality of both threshold proxy signing and encryption, and provides fair protection for the sender and the proxy agents. This scheme is secure against attack of public key substitution. It also satisfies security properties such as confidentiality and authenticity.     

白云鄂博主矿开拓运输工艺转换有关问题的探讨

本文对白云鄂博主矿采场铁公路联合运输向公路运输转换位置是否确定为1638m水平以及运输工艺转换过程中相关问题进行分析论证，提出主矿采场铁路至少可向下延深一个水平，技术上可行，节约运费千万元以上。     

Investigation of the Correlation between Texture and Microstructure on a Submicrometer Scale in the TEM

In recent years the investigation of local texture and microstructure by analysis of electron backscatter diffraction patterns (EBSP) in the SEM has become a very powerful and popular method. With the introduction of SEM with field emission guns (FEG) the spatial resolution of EBSP measurements could be enhanced from 500 nm with a tungsten emitter to better than 50 nm. This evolution of SEM techniques raises the question whether transmission electron microscopy (TEM) still has fields of application in texture research. The present article answers this question with a clear “yes” and presents three examples of investigations where TEM is indispensable. The three examples comprise the investigation of the correlation between dislocation structure and deformation texture, a study on nucleation mechanisms of recrystallization in highly deformed metals and the investigation of microtexture and microstructure in nanocrystalline materials. Together with the presentation of these cases some of the necessary measurement techniques are described briefly. It is shown that TEM has to be applied when highest spatial resolution of orientation determination and imaging and high accuracy of orientation determination are to be reached, when the three‐dimensional and quantitative characterization of lattice defects is required or when materials with a high density of lattice defects are to be investigated.     

WDB620高强钢应用于大型蜗壳的焊接制造工艺研究

2005年初,水电十四局承担了漫湾二期水电站和小湾水电站蜗壳的制造任务。蜗壳钢材选用国产600 MPa级别高强钢,为了全面综合地考核该级别钢种的材料强度和安全裕度,检验模拟大型蜗壳焊接制造工艺的可靠性。对国产的WDB620高强钢进行了可焊性和制造工艺性试验研究,并在国内首次设计、制造模拟压力容器并对其进行水压试验和爆破试验。研究成果通过中国水电集团公司鉴定,结论为该课题研究成果达到国内选进水平。     

厦门市气源转换的技术分析

分析了气源转换时原有输配系统的管道、调压设备、计量设备、用气设备与天然气系统相适应的问题，提出了相应的措施。