Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.     

Viscoelastic Behavior of Synthesized Liquid Soaps and Surface Activity Properties of Surfactants

In the present work, a rheological study of liquid soaps prepared from different mixture of surfactants as a function of surfactant type and concentration was performed. The curves of shear stress vs. shear rate and viscosity vs. shear rate were recorded at constant temperature, 294 ± 0.1 K. The surface activity properties were also studied. The results of the study showed that values of surface tension, γ, were in the range 31–40 mN m⁻¹ and the critical micelle concentration (CMC), was of the order 10⁻⁴ mol L⁻¹. The calculated maximum surface excess, Γ_max, varied from 2.40 to 3.66 μmol m⁻², while minimum area per molecule, A_min, varied from 41.1 (for amphoterics) to 81.4 Ų (for nonionic surfactants). The standard free energy of micellization, −29.8 and −29.3 kJ mol⁻¹ for anionic and amphoteric surfactants, respectively, were while values for nonionic surfactants varied between −31.8 and − 30.3 kJ mol⁻¹. The free energy of adsorption, was the lowest for amphoteric surfactants (−37.9 kJ mol⁻¹), followed by anionics (−40.4 kJ mol⁻¹) and nonionics (−43.34 to −46.84 kJ mol⁻¹), indicating that micellization process is spontaneous in the examined medium. The synthetized liquid soaps show pseudoplastic behavior and they achieved pipe flow. The results of this research indicate that flow behavior was affected significantly by the ionic charge of the surfactant and the ionic strength of the formulation, suggesting that the flow behavior could be changed by manipulating the choice of the surfactant and salinity. The pH value of all liquid soaps examined were weakly acidic, in the range of 5.0–6.4.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Computational studies on the radiative and nonradiative processes of luminescent N-heteroleptic platinum(II) complexes

Three N-heteroleptic Pt(II) complexes, [Pt(C^C)(O^O)] [O^O = acetylacetonate, C^C = 1-phenyl-1,2,4-triazol-5-ylidene (1), C^C = 4-phenyl-1,2,4-triazol-5-ylidene (2), C^C = 2-phenylpyrazine (3)] have been investigated with density functional theory (DFT) and time-dependent density functional theory (TDDFT). The radiative decay rate constants of complexes 1–3 have been discussed with the oscillator strength (f_n), the strength of spin–orbit coupling (SOC) interaction between the lowest energy triplet excited state (T₁) and singlet excited states (S_n), and the energy gaps between E(T₁) and E(S_n). To illustrate the nonradiative decay processes, the transition states between triplet metal-centered (³MC) and T₁ states have been optimized and were verified with the calculations of vibrational frequencies and intrinsic reaction coordinate (IRC). In addition, the minimum energy crossing points (MECPs) between ³MC and ground states (S₀) were optimized. At last, the potential energy curves relevant to the nonradiative decay pathways are simulated. The results show that complex 3 has the biggest photoluminescence quantum yield because the complex 3 has the biggest radiative decay rate constant and the smallest nonradiative decay rate constant in complexes 1–3.     

Polyaniline-based networks combined with Fe3O4 hollow spheres and carbon balls for excellent electromagnetic wave absorption

Polyaniline (PANI)-based networks combined with Fe₃O₄ hollow spheres and carbon balls (FCP) for improved electromagnetic wave (EMW) absorption were investigated using an easy-to-industrialize solvothermal and physical method. Hollow structure Fe₃O₄ spheres with a lower density than that of the common solid sphere were prepared. As a thin and light magnetic material, Fe₃O₄ hollow spheres generate magnetic loss, carbon balls and PANI networks generate dielectric loss. The magnetic and conductive parts play appropriate roles in achieving complementarity in the EMW absorption. The relatively high specific surface area introduced by PANI networks promotes interfacial polarization and further supports dielectric loss. In conclusion, the above reasons provide multiple attenuation mechanisms. Samples FCP1 (?65.109 dB, at 12.800 GHz, 1.966 mm, from 5.6 to 18.0 GHz) and FCP2 (?61.033 dB, at 8.480 GHz, 3.328 mm, from 4.3 to 18.0 GHz) demonstrated a wide bandwidth, a small thickness, a minimum reflection loss (R_L), and a low loading ratio (25%) in paraffin-based composites. Specifically, their loading ration of 25% is much lower than the loading ratio of conventional materials (usually 50% and above). In addition, the bandwidth is excessively wide, above 12 GHz, possessing good absorption performance in continuous intervals with different thicknesses. Such excellent characteristics have rarely been reported in literature.